BRADY

SPEEDAIRE

Office & School Consumables

office-school-consumables

Label Papers

label-papers

Mechanical Parts

mechanical-parts

O Ring

o-ring

Office Supplies

office-supplies

Pneumatic Air Tools & Equipments

pneumatic-air-tools-equipments

Pneumatic Hose Reels

pneumatic-hose-reels

Silicone O-Rings are sometimes referred to VMQ O-Rings.

Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility. 

In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.

Overview on Application Rating for Material Silicone 

Heat Ozone & Aging Resistance - Excellent

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/H~vR5oaK9sd8wYuX1KFGuq.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P62
&nbsp;ID 61.60 x CS 5.70&nbsp;
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:86h6n"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/H~vR5oaK9sd8wYuX1KFGuq.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="86h6n" 
 layout="nodisplay"></amp-image-lightbox>

John

Others

Optibelt

Gates

SAMTECH

VITON

V Rings

Rubber Seals

Oil Seals

Shaft Couplings

Plumbing Tools & Equipment

Ball Bearings

Hydraulic Seals

Wall Plugs, Anchors, Fixings & Kits

Vee-Belts

buyerIntroduction

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Silicone 70 Shore

oring jis b2401 p62 id 61.60 cs 5.70 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 5.70硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-p62-id-61-60-x-cs-5-70-silicone-70-shore

Nitrile is often referred to Buna (Buna-N) and NBR.

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C). 

It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.

However Nitrile are not a restricting factors in many applications.

Overview on Application Rating for Material Nitrile (NBR) 

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/UFX382rJ_zX8LNWmxjL3NE.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P62
&nbsp;ID 61.60 x CS 5.70&nbsp;
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:752rj"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/UFX382rJ_zX8LNWmxjL3NE.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="752rj" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Nitrile (NBR) 70 Shore

oring jis b2401 p62 id 61.60 cs 5.70 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 5.70丁腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p62-id-61-60-x-cs-5-70-nitrile-nbr-70-shore

ORING JIS B2401 G85 ID 84.40 x CS 3.10Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/51GSFtXRgqS_BIp17Ktv1P.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G85
&nbsp;ID 84.40 x CS 3.10
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:el2q0"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/51GSFtXRgqS_BIp17Ktv1P.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="el2q0" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 G85 ID 84.40 x CS 3.10 Silicone 70 Shore

oring jis b2401 g85 id 84.40 cs 3.10 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.10硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-g85-id-84-40-x-cs-3-10-silicone-70-shore

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).  

Overview on Application Rating for Material Nitrile (NBR)  

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.  

Applications that require resistance to OIL 

Applications that are required to work in low temperatures (-0°C) 

High performance Fuel systems that requires strictly no leakage

Covering 	and lubricating the threading of the shaft 

ORING AS568 AS143 ID 61.60 X CS 2.62Material : Nitrile (NBR) 70 ShoreAdditional InformationNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Primary UsageO-Rings and rubber seals are generally used for:<ul class="md-block-unordered-list-item"><li>Applications that require resistance to OIL </li><li>Applications that are required to work in low temperatures (-0°C) </li><li>High performance Fuel systems that requires strictly no leakage</li><ul class="md-block-unordered-list-item"><li>Aircrafts </li><li>Marine Ships </li><li>F1 Cars</li></ul><li>General Industrial Use </li></ul>Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:<ul class="md-block-unordered-list-item"><li>Covering 	and lubricating the threading of the shaft </li></ul>The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.<ul class="md-block-unordered-list-item"><li>Don’t force it over sharp corners </li></ul>That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.<ul class="md-block-unordered-list-item"><li>Even stretching </li></ul>You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.<ul class="md-block-unordered-list-item"><li>Don’t roll it down the shaft </li></ul>Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.<ul class="md-block-unordered-list-item"><li>Finishing 	it off </li></ul>Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/4sPUEO5oandYJxlTFXFMEQ.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS143
&nbsp;ID 61.60 X CS 2.62
Material : Nitrile (NBR) 70 Shore
<ins>Additional Information</ins>
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>&nbsp;
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.&nbsp;&nbsp;
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
<ul>
<li>Applications that require resistance to OIL&nbsp;</li>
<li>Applications that are required to work in low temperatures (-0°C)&nbsp;</li>
<li>High performance Fuel systems that requires strictly no leakage</li>
<ul>
<li>Aircrafts&nbsp;</li>
<li>Marine Ships&nbsp;</li>
<li>F1 Cars</li>
</ul>
<li>General Industrial Use&nbsp;&nbsp;&nbsp;</li>
</ul>
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
<ul>
<li>Covering 	and lubricating the threading of the shaft&nbsp;</li>
</ul>
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
<ul>
<li>Don’t force it over sharp corners&nbsp;</li>
</ul>
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
<ul>
<li>Even stretching&nbsp;</li>
</ul>
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
<ul>
<li>Don’t roll it down the shaft&nbsp;</li>
</ul>
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
<ul>
<li>Finishing 	it off&nbsp;</li>
</ul>
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:1strn"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/4sPUEO5oandYJxlTFXFMEQ.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="1strn" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS143 ID 61.60 X CS 2.62 Nitrile (NBR) 70 Shore

oring as568 as143 id 61.60 cs 2.62 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 2.62腈（nbr）70肖氏 o型圈 oem代工

oring-as568-as143-id-61-60-x-cs-2-62-nitrile-nbr-70-shore

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.

ORING AS568 AS143 ID 61.60 X CS 2.62Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/bsy7C2~MlMR36Grl30NRfl.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS143
&nbsp;ID 61.60 X CS 2.62
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:eohqp"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/bsy7C2~MlMR36Grl30NRfl.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="eohqp" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS143 ID 61.60 X CS 2.62 Silicone 70 Shore

oring as568 as143 id 61.60 cs 2.62 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 2.62硅胶70邵氏 o型圈 oem代工

oring-as568-as143-id-61-60-x-cs-2-62-silicone-70-shore

ORING JIS B2401 P70 ID 69.60 x CS 5.70Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/_O~cEOrdxc9kN4gkTcDrvz.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P70&nbsp;
ID 69.60 x CS 5.70
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bngab"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/_O~cEOrdxc9kN4gkTcDrvz.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bngab" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P70 ID 69.60 x CS 5.70 Nitrile (NBR) 70 Shore

oring jis b2401 p70 id 69.60 cs 5.70 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 5.70腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p70-id-69-60-x-cs-5-70-nitrile-nbr-70-shore

 Speedaire 6WA70 Spring Return Hose Reel 3/8 in Id 35 Ft

Mounting Location: Floor, Ceiling, Wall
 

<h3 class="md-block-header-three"> Speedaire 6WA70 Spring Return Hose Reel 3/8 in Id 35 Ft</h3><ul class="md-block-unordered-list-item"><li>Part Number: 6WA70 </li><li>Mfg Part Number: 6WA70 </li><li>Fitting Size: 3/8 in x 1/4 in </li><li>Includes Hose: Yes </li><li>Mounting Location: Floor, Ceiling, Wall </li><li>Number of Guide Arms: Single Arm </li><li>Swivel Material: Brass </li><li>Hose Capacity: 33 ft (3/8 in I.D.) </li><li>Pedestal Type: - </li><li>Reel Color: Green </li><li>Maximum Operating Pressure: 300 psi </li><li>Reel Material: Steel </li><li>Drive Type: Spring Return </li><li>Enclosed: No </li><li>Fitting Type: NPT x NPT </li><li>Speed Limited Retraction: No</li></ul>

<h3> Speedaire 6WA70 Spring Return Hose Reel 3/8 in Id 35 Ft</h3>
<ul>
<li>Part Number: 6WA70 
&nbsp;</li>
<li>Mfg Part Number: 6WA70 
&nbsp;</li>
<li>Fitting Size: 3/8 in x 1/4 in 
&nbsp;</li>
<li>Includes Hose: Yes 
&nbsp;</li>
<li>Mounting Location: Floor, Ceiling, Wall 
&nbsp;</li>
<li>Number of Guide Arms: Single Arm 
&nbsp;</li>
<li>Swivel Material: Brass 
&nbsp;</li>
<li>Hose Capacity: 33 ft (3/8 in I.D.) 
&nbsp;</li>
<li>Pedestal Type: - 
&nbsp;</li>
<li>Reel Color: Green 
&nbsp;</li>
<li>Maximum Operating Pressure: 300 psi 
&nbsp;</li>
<li>Reel Material: Steel 
&nbsp;</li>
<li>Drive Type: Spring Return 
&nbsp;</li>
<li>Enclosed: No 
&nbsp;</li>
<li>Fitting Type: NPT x NPT 
&nbsp;</li>
<li>Speed Limited Retraction: No</li>
</ul>

Grainger

Speedaire 6WA70 Spring Return Hose Reel 3/8 in Id 35 Ft

speedaire 6wa70 spring return hose reel 3/8 id 35ft gulungan selang pegas pneumatic reels pneumatik hos gelong speedaire/速必达 弹簧回位软管卷盘 英寸 内径 英尺 气动软管卷盘 速达

speedaire-6wa70-spring-return-hose-reel-3-8-in-id-35-ft

Material : Ethylene Propylene Diene Monomer (EPDM) 70 Shore      

Ethylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.

EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51`C to 149`C) and it has good retention of compression.

In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance. 

The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.

Overview on Application Rating for Material EPDM

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.

ORING AS568 AS143 ID 61.60 X CS 2.62Material : Ethylene Propylene Diene Monomer (EPDM) 70 Shore Additional InformationEthylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51&#x60;C to 149&#x60;C) and it has good retention of compression.In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance. The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.Temperature Range (Dry Heat)Low: -60&#x60;F / -51&#x60;C High: 300&#x60;F / 149&#x60;COverview on Application Rating for Material EPDMProperties (Rating)Petroleum Oils / Fuels - PoorSteam Up to 399&#x60;F– ExcellentGas Impermeability - GoodCompressiom - GoodAbrasion Resistance - GoodOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/yO~OLWGXjYSm3jvMBJubsW.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS143
&nbsp;ID 61.60 X CS 2.62
Material : Ethylene Propylene Diene Monomer (EPDM) 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;
<ins>Additional Information</ins>
Ethylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.
EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51`C to 149`C) and it has good retention of compression.
In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance.&nbsp;
The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.
<ins>Temperature Range (Dry Heat)</ins>
Low: -60`F / -51`C High: 300`F / 149`C
<ins>Overview on Application Rating for Material EPDM</ins>
Properties (Rating)
Petroleum Oils / Fuels - Poor
Steam Up to 399`F– Excellent
Gas Impermeability - Good
Compressiom - Good
Abrasion Resistance - Good
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:2m9j4"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/yO~OLWGXjYSm3jvMBJubsW.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="2m9j4" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS143 ID 61.60 X CS 2.62 Ethylene Propylene Diene Monomer (EPDM) 70 Shore

oring as568 as143 id 61.60 cs 2.62 ethylene propylene diene monomer (epdm) 70 shore ring o-ring oem gelang oem/oem代工 2.62乙烯丙烯二烯单体（epdm）70肖氏 o型圈 oem代工

oring-as568-as143-id-61-60-x-cs-2-62-ethylene-propylene-diene-monomer-epdm-70-shore

ORING JIS B2401 P58 ID 57.60 x CS 5.70Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/UkmQO3zKGSW3JloGg427z8.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P58&nbsp;
ID 57.60 x CS 5.70
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:7q56t"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/UkmQO3zKGSW3JloGg427z8.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="7q56t" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P58 ID 57.60 x CS 5.70 Nitrile (NBR) 70 Shore

oring jis b2401 p58 id 57.60 cs 5.70 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 5.70丁腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p58-id-57-60-x-cs-5-70-nitrile-nbr-70-shore

ORING AS568 AS311 ID 13.64 x CS 5.33Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS311
&nbsp;ID 13.64 x CS 5.33
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:vggt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="vggt" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS311 ID 13.64 x CS 5.33 Silicone 70 Shore

oring as568 as311 id 13.64 cs 5.33 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 5.33硅胶70肖氏 o型圈 oem代工

oring-as568-as311-id-13-64-x-cs-5-33-silicone-70-shore

Material :Ethylene Propylene Diene Monomer (EPDM) 70 Shore    

ORING AS568 AS252 ID 132.94 x CS 3.53Material :Ethylene Propylene Diene Monomer (EPDM) 70 Shore Additional InformationEthylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51&#x60;C to 149&#x60;C) and it has good retention of compression.In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance. The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.Temperature Range (Dry Heat)Low: -60&#x60;F / -51&#x60;C High: 300&#x60;F / 149&#x60;COverview on Application Rating for Material EPDMProperties (Rating)Petroleum Oils / Fuels - PoorSteam Up to 399&#x60;F– ExcellentGas Impermeability - GoodCompressiom - GoodAbrasion Resistance - GoodOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/PHXGn_9dqp2XR4sY~Dgzeb.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS252&nbsp;
ID 132.94 x CS 3.53
Material :Ethylene Propylene Diene Monomer (EPDM) 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
<ins>Additional Information</ins>
Ethylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.
EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51`C to 149`C) and it has good retention of compression.
In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance.&nbsp;
The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.
<ins>Temperature Range (Dry Heat)</ins>
Low: -60`F / -51`C High: 300`F / 149`C
<ins>Overview on Application Rating for Material EPDM</ins>
Properties (Rating)
Petroleum Oils / Fuels - Poor
Steam Up to 399`F– Excellent
Gas Impermeability - Good
Compressiom - Good
Abrasion Resistance - Good
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:7i66f"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/PHXGn_9dqp2XR4sY~Dgzeb.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="7i66f" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS252 ID 132.94 x CS 3.53 Ethylene Propylene Diene Monomer (EPDM) 70 Shore

oring as568 as252 id 132.94 cs 3.53 ethylene propylene diene monomer (epdm) 70 shore ring o-ring oem gelang oem/oem代工 3.53乙烯丙烯二烯单体（epdm）70肖氏 o型圈 oem代工

oring-as568-as252-id-132-94-x-cs-3-53-ethylene-propylene-diene-monomer-epdm-70-shore

ORING JIS B2401 P62 \ID 61.60 x CS 5.70 Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/ub4Qd0WgbOHtLw1gDDhuF~.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P62 \
ID 61.60 x CS 5.70&nbsp;
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bripl"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/ub4Qd0WgbOHtLw1gDDhuF~.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bripl" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Nitrile (NBR) 90 Shore

oring jis b2401 p62 id 61.60 cs 5.70 nitrile (nbr) 90 shore ring o-ring oem gelang oem/oem代工 5.70丁腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p62-id-61-60-x-cs-5-70-nitrile-nbr-90-shore

ORING AS568 AS149 ID 71.12 X CS 2.62Material : Ethylene Propylene Diene Monomer (EPDM) 70 Shore Additional InformationEthylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51&#x60;C to 149&#x60;C) and it has good retention of compression.In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance. The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.Temperature Range (Dry Heat)Low: -60&#x60;F / -51&#x60;C High: 300&#x60;F / 149&#x60;COverview on Application Rating for Material EPDMProperties (Rating)Petroleum Oils / Fuels - PoorSteam Up to 399&#x60;F– ExcellentGas Impermeability - GoodCompressiom - GoodAbrasion Resistance - GoodOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/pNmd61Mkij~zF2q5Z7XX4X.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS149
&nbsp;ID 71.12 X CS 2.62
Material : Ethylene Propylene Diene Monomer (EPDM) 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;
<ins>Additional Information</ins>
Ethylene-propylene diene monomer O-Rings are sometimes referred to EPDM rubber as it is normally compounded with a third monomer to produce it.
EPDM elastomers are an excellent material for sealing brake systems and in hot water and steam applications. Due to its outstanding resistance to extreme range of temperature ranging from (-51`C to 149`C) and it has good retention of compression.
In addition EPDM elastomer perform good resistance to mild acids, detergents, alkalis, silicone oils and greases, ketones, and alcohols. EPDM is widely accepted by user in the seal industry by its excellent chemical resistance properties and its superb ozone resistance.&nbsp;
The down side for applications with petroleum oils, mineral oil, die-ester lubricants or fuel exposure EPDM is not recommended.
<ins>Temperature Range (Dry Heat)</ins>
Low: -60`F / -51`C High: 300`F / 149`C
<ins>Overview on Application Rating for Material EPDM</ins>
Properties (Rating)
Petroleum Oils / Fuels - Poor
Steam Up to 399`F– Excellent
Gas Impermeability - Good
Compressiom - Good
Abrasion Resistance - Good
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. EPDM O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:7vdjn"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/pNmd61Mkij~zF2q5Z7XX4X.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="7vdjn" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS149 ID 71.12 X CS 2.62 Ethylene Propylene Diene Monomer (EPDM) 70 Shore

oring as568 as149 id 71.12 cs 2.62 ethylene propylene diene monomer (epdm) 70 shore ring o-ring oem gelang oem/oem代工 2.62乙烯丙烯二烯单体（epdm）70肖氏 o型圈 oem代工

oring-as568-as149-id-71-12-x-cs-2-62-ethylene-propylene-diene-monomer-epdm-70-shore

Material :  Viton Fluoroelastomers (FKM) 75 Shore   

Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.

This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).

In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. 

The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.

O-Rings, rubber seals and custom molded rubber components for:

High temperature applications requiring good compression      set

Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.

When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.

The following steps should help in installing an O-ring correctly and saving time as well:

1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.

2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.

3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.

4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.

5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.

Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings, rubber seals and custom molded rubber components for: <ul class="md-block-unordered-list-item"><li>Automotive fuel handling</li><li>Aircraft engine seals</li><li>High temperature applications requiring good compression set</li><li>General industrial O-ring seals</li></ul>Important Tips When Installing an O-RingProper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.Installing an O-RingWhen installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.Tips for Better Installation of O-RingsThe following steps should help in installing an O-ring correctly and saving time as well:1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 P62
&nbsp;ID 61.60 x CS 5.70&nbsp;
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings, rubber seals and custom molded rubber components for:

<ul>
<li>Automotive fuel handling</li>
<li>Aircraft engine seals</li>
<li>High temperature applications requiring good compression set</li>
<li>General industrial O-ring seals</li>
</ul>
<ins>Important Tips When Installing an O-Ring</ins>
Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.
Installing an O-Ring
When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.
Tips for Better Installation of O-Rings
The following steps should help in installing an O-ring correctly and saving time as well:
1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.
2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.
3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.
4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.
5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.
Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 P62 ID 61.60 x CS 5.70 Viton Fluoroelastomers (FKM) 75 Shore

oring jis b2401 p62 id 61.60 cs 5.70 viton fluoroelastomers (fkm) 75 shore fluoroelastomer ring o-ring oem gelang oem/oem代工 5.70氟橡胶（fkm）75肖氏 o型圈 oem代工

oring-jis-b2401-p62-id-61-60-x-cs-5-70-viton-fluoroelastomers-fkm-75-shore

This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).

ORING JIS B2401 G55 ID 54.40 x CS 3.10Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/Q0Zf97W3TvWRLp9Wmvms3n.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G55&nbsp;
ID 54.40 x CS 3.10
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:8unr2"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/Q0Zf97W3TvWRLp9Wmvms3n.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="8unr2" 
 layout="nodisplay"></amp-image-lightbox>

Parker

Washers

ORING JIS B2401 G55 ID 54.40 x CS 3.10 Viton Fluoroelastomers (FKM) 75 Shore

oring jis b2401 g55 id 54.40 cs 3.10 viton fluoroelastomers (fkm) 75 shore fluoroelastomer ring o-ring oem gelang oem/oem代工 3.10氟橡胶（fkm）75肖氏 o型圈 oem代工

oring-jis-b2401-g55-id-54-40-x-cs-3-10-viton-fluoroelastomers-fkm-75-shore

ORING AS568 AS143 ID 61.60 X CS 2.62Material : Nitrile (NBR) 90 Shore Additional InformationNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Primary UsageO-Rings and rubber seals are generally used for:<ul class="md-block-unordered-list-item"><li>Applications that require resistance to OIL </li><li>Applications that are required to work in low temperatures (-0°C) </li><li>High performance Fuel systems that requires strictly no leakage</li><ul class="md-block-unordered-list-item"><li>Aircrafts </li><li>Marine Ships </li><li>F1 Cars</li></ul><li>General Industrial Use </li></ul>Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:<ul class="md-block-unordered-list-item"><li>Covering 	and lubricating the threading of the shaft </li></ul>The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.<ul class="md-block-unordered-list-item"><li>Don’t force it over sharp corners </li></ul>That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.<ul class="md-block-unordered-list-item"><li>Even stretching </li></ul>You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.<ul class="md-block-unordered-list-item"><li>Don’t roll it down the shaft </li></ul>Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.<ul class="md-block-unordered-list-item"><li>Finishing 	it off </li></ul>Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/YOaeFb_v3jrGN~DEEdVVMJ.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS143
&nbsp;ID 61.60 X CS 2.62
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
<ins>Additional Information</ins>
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>&nbsp;
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.&nbsp;&nbsp;
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
<ul>
<li>Applications that require resistance to OIL&nbsp;</li>
<li>Applications that are required to work in low temperatures (-0°C)&nbsp;</li>
<li>High performance Fuel systems that requires strictly no leakage</li>
<ul>
<li>Aircrafts&nbsp;</li>
<li>Marine Ships&nbsp;</li>
<li>F1 Cars</li>
</ul>
<li>General Industrial Use&nbsp;&nbsp;&nbsp;</li>
</ul>
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
<ul>
<li>Covering 	and lubricating the threading of the shaft&nbsp;</li>
</ul>
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
<ul>
<li>Don’t force it over sharp corners&nbsp;</li>
</ul>
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
<ul>
<li>Even stretching&nbsp;</li>
</ul>
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
<ul>
<li>Don’t roll it down the shaft&nbsp;</li>
</ul>
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
<ul>
<li>Finishing 	it off&nbsp;</li>
</ul>
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:d8ib0"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/YOaeFb_v3jrGN~DEEdVVMJ.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="d8ib0" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS143 ID 61.60 X CS 2.62 Nitrile (NBR) 90 Shore

oring as568 as143 id 61.60 cs 2.62 nitrile (nbr) 90 shore ring o-ring oem gelang oem/oem代工 2.62腈（nbr）90肖氏 o型圈 oem代工

oring-as568-as143-id-61-60-x-cs-2-62-nitrile-nbr-90-shore

Self-Laminating Vinyl (B-427) is an excellent material for wire and cable identification. This material has good clarity, conformability and is self-extinguishing.

Provided in a self-laminated format with a white printable zone and translucent overlaminating area to protect text

Durable, permanent acrylic adhesive has outstanding water and oil resistance

Service temperature of -40°F to 158°F (-40°C to 70°C)

A ribbon is required to print this material. Use Part Number M61-R4310 for the BMP®61 Label Printer / BradyPrinter M611 Mobile Label Printer or M71-R4300 for the BMP®71 Label Printer

Applications: Cable & Wire Marking, Panel Labeling, Voice & Data ID

HTS Code (Harmonized Tariff Schedule): 8443.99.2550

ECCN (Export Commodity Control Number): EAR99

Printable Area Dimensions: 0.5 in H x 1 in W

Material Properties: Flame-retardant, Self-laminating

Label Properties: Self Laminating & Wrap Around

Resistance Properties: Chemical-Resistant, Humidity-Resistant, Oil-Resistant, Water-Resistant, Weather-Resistant

Service Temperature Range °F: -94 °F - 158 °F

Application: Data and Telecommunications Labeling, Electrical Labeling, Laboratory Labeling, Wire and Cable Labeling

For Use with Printer: BMP®61 Label Printer, BMP®71 Label Printer, BradyPrinter M611 Mobile Label Printer

Wire Diameter Range: 0.157 in to 0.319 in

Pre-Printed Areas on Label: Colored Write-On Area

RoHS Compliance Status: Compliant with Directive 2011/65/EU and 2015/863 

<h3 class="md-block-header-three">BM71-31-427</h3>OverviewSelf-Laminating Vinyl (B-427) is an excellent material for wire and cable identification. This material has good clarity, conformability and is self-extinguishing.<ul class="md-block-unordered-list-item"><li>Provided in a self-laminated format with a white printable zone and translucent overlaminating area to protect text</li><li>Durable, permanent acrylic adhesive has outstanding water and oil resistance</li><li>UL approved</li><li>Service temperature of -40°F to 158°F (-40°C to 70°C)</li><li>A ribbon is required to print this material. Use Part Number M61-R4310 for the BMP®61 Label Printer / BradyPrinter M611 Mobile Label Printer or M71-R4300 for the BMP®71 Label Printer</li></ul> SpecificationsKey CharacteristicsUPC: 662820926634Applications: Cable &amp; Wire Marking, Panel Labeling, Voice &amp; Data IDUOM: Roll of 2500 LabelsQuantity per Roll: 2500Trade Name: BMP®71Brand Name: Brady®Country of Origin: MexicoHTS Code (Harmonized Tariff Schedule): 8443.99.2550ECCN (Export Commodity Control Number): EAR99 DimensionsDimensions: 1.5 in H x 1 in WHeight: 1.5 inWidth: 1 inLabel/Tape Size: 1.5 in H x 1 in WPrintable Area Dimensions: 0.5 in H x 1 in WPrintable Area Height: 0.5 inPrintable Area Width: 1 inThickness: 0.004 inVertical Repeat: 1.125 inWeb Width: 1.812 inVial/Tube Size: 50.0 ml Material CharacteristicsMaterial Number: B-427Material: Self-laminating VinylMaterial Properties: Flame-retardant, Self-laminatingLabel Properties: Self Laminating &amp; Wrap AroundAdhesive Type: Permanent AcrylicFinish: MatteColor: White, ClearResistance Properties: Chemical-Resistant, Humidity-Resistant, Oil-Resistant, Water-Resistant, Weather-ResistantIndoor or Outdoor Use: Outdoor UseService Temperature Range °F: -94 °F - 158 °FMinimum Service Temperature °F: -94 °FMinimum Service Temperature °F: -94 °FMaximum Service Temperature °F: 158 °FCompatible Surface Types: General Product FeaturesApplication: Data and Telecommunications Labeling, Electrical Labeling, Laboratory Labeling, Wire and Cable LabelingShape: RectangleCorner Type: Rounded CornersLabel/Media Format: Bulk RollQuantity per Row: 1 Printing SpecificationsPrint Technology: Thermal Transfer CompatibilityFor Use with Printer: BMP®61 Label Printer, BMP®71 Label Printer, BradyPrinter M611 Mobile Label PrinterRecommended Ribbon: M61-R4310, M71-R4300Suggested Ribbon Series: R4300, R4500Wire Diameter Range: 0.157 in to 0.319 inWire Gauge Range: 10 AWG - 4 AWG Preprinted InformationPre-Printed Areas on Label: Colored Write-On Area ComplianceUNSPSC: 55121612RoHS Compliance Status: Compliant with Directive 2011/65/EU and 2015/863

<h3>BM71-31-427</h3>
Overview
Self-Laminating Vinyl (B-427) is an excellent material for wire and cable identification. This material has good clarity, conformability and is self-extinguishing.
<ul>
<li>Provided in a self-laminated format with a white printable zone and translucent overlaminating area to protect text</li>
<li>Durable, permanent acrylic adhesive has outstanding water and oil resistance</li>
<li>UL approved</li>
<li>Service temperature of -40°F to 158°F (-40°C to 70°C)</li>
<li>A ribbon is required to print this material. Use Part Number M61-R4310 for the BMP®61 Label Printer / BradyPrinter M611 Mobile Label Printer or M71-R4300 for the BMP®71 Label Printer</li>
</ul>
&nbsp;
Specifications
Key Characteristics
UPC: 662820926634
Applications: Cable &amp; Wire Marking, Panel Labeling, Voice &amp; Data ID
UOM: Roll of 2500 Labels
Quantity per Roll: 2500
Trade Name: BMP®71
Brand Name: Brady®
Country of Origin: Mexico
HTS Code (Harmonized Tariff Schedule): 8443.99.2550
ECCN (Export Commodity Control Number): EAR99

Dimensions
Dimensions: 1.5 in H x 1 in W
Height: 1.5 in
Width: 1 in
Label/Tape Size: 1.5 in H x 1 in W
Printable Area Dimensions: 0.5 in H x 1 in W
Printable Area Height: 0.5 in
Printable Area Width: 1 in
Thickness: 0.004 in
Vertical Repeat: 1.125 in
Web Width: 1.812 in
Vial/Tube Size: 50.0 ml

Material Characteristics
Material Number: B-427
Material: Self-laminating Vinyl
Material Properties: Flame-retardant, Self-laminating
Label Properties: Self Laminating &amp; Wrap Around
Adhesive Type: Permanent Acrylic
Finish: Matte
Color: White, Clear
Resistance Properties: Chemical-Resistant, Humidity-Resistant, Oil-Resistant, Water-Resistant, Weather-Resistant
Indoor or Outdoor Use: Outdoor Use
Service Temperature Range °F: -94 °F - 158 °F
Minimum Service Temperature °F: -94 °F
Minimum Service Temperature °F: -94 °F
Maximum Service Temperature °F: 158 °F
Compatible Surface Types: General

Product Features
Application: Data and Telecommunications Labeling, Electrical Labeling, Laboratory Labeling, Wire and Cable Labeling
Shape: Rectangle
Corner Type: Rounded Corners
Label/Media Format: Bulk Roll
Quantity per Row: 1

Printing Specifications
Print Technology: Thermal Transfer

Compatibility
For Use with Printer: BMP®61 Label Printer, BMP®71 Label Printer, BradyPrinter M611 Mobile Label Printer
Recommended Ribbon: M61-R4310, M71-R4300
Suggested Ribbon Series: R4300, R4500
Wire Diameter Range: 0.157 in to 0.319 in
Wire Gauge Range: 10 AWG - 4 AWG

Preprinted Information
Pre-Printed Areas on Label: Colored Write-On Area

Compliance
UNSPSC: 55121612
RoHS Compliance Status: Compliant with Directive 2011/65/EU and 2015/863&nbsp;

Izon Ng 

Panduit

Band-It

Brother

Brady Bulk Self-Laminating Vinyl Labels for BMP61 BMP71 M611 - 1.5" X 1"

brady bulk self-laminating vinyl labels bmp61 bmp71 m611 1.5" 1" massal untuk label papers kertas pelapis sendiri pukal 用于 brady/布雷迪 散装自层压乙烯基标签 标签纸 布雷迪