CAT PUMPS

DAYTON

Enerpac

Hydratron

Ingco

Jabsco

MITSUBISHI

SPX POWER TEAM

Pumps

pumps

Hand Pumps

hand-pumps

Hydraulic Machinery & Equipment

hydraulic-machinery-equipment

Hydraulic Pumps

hydraulic-pumps

Metering Pumps

metering-pumps

Water Pumps

water-pumps

 This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of 316SS manifold, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as DI water and salt water. 

Inlet Pressure v Water Temperature Vaporization and Caviation Analaysis

With ambient temperatures, piston pumps can handle a maximum negative suction of -8.5 psi (20 feet of water) and plunger  pumps can handle a maximum negative suction -5 psi (11.5 feet of water). As the temperature of the water increases, the vapor  pressure (pressure required to remain liquid) also increases. By increasing the inlet pressure to the pump, you can minimize the  increased risk of cavitation.  To achieve the recommended inlet pressures with elevated temperatures, it is often necessary to use a booster pump. The booster  pump should be approximately twice the system capacity to assure adequate flow into the pump. See chart on front page.  REDUCTION IN RPM In addition to increasing the inlet pressure to the pump as temperature increases, reducing the pump rpm will also offer added  protection. Reducing the rpm reduces the acceleration and vaporization of the water. Lower rpm reduces the risk of cavitation and  its damaging effects. See chart on front for recommended rpm.

 If more than 5-6 feet from the pump or long feed lines or a booster pump or high temperature are present, an inlet stabilizer  should be installed to stabilize inlet pressure.  Note: An inlet stabilizer will not function with a negative suction inlet. INCREASED LINE SIZE It is always important to have the inlet supply line sized to match or be one size larger than the pump inlet port for optimum  performance, but it is most critical when the pumped liquid is at elevated temperatures. Under sizing the line will only compound  the problems of high temperature vaporization. See individual pump data sheet. 

The optimum installation for ambient temperature water requires a properly sized baffled supply tank. The tank should be  enclosed and 6-10 times the system capacity with at least two baffles. 

Introduction: This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of 316SS manifold, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as DI water and salt water. Technical Specifications:Max Flow: 10 gpm / 37.9 lpmMax Pressure: 2200Inlet Port: Size3/4&quot; NPT(F)Discharge Port Size1/2&quot; NPT(F)RPM: 958Drive Type(s): Belt, ClutchMaterial316 Stainless SteelInlet Pressure v Water Temperature Vaporization and Caviation Analaysis<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/mCAnnKkJMK3J3Qw6J5zc3x.jpg" alt="" /><figcaption class="md-block-image-caption"></figcaption></figure> PRESSURIZED INLET With ambient temperatures, piston pumps can handle a maximum negative suction of -8.5 psi (20 feet of water) and plunger pumps can handle a maximum negative suction -5 psi (11.5 feet of water). As the temperature of the water increases, the vapor pressure (pressure required to remain liquid) also increases. By increasing the inlet pressure to the pump, you can minimize the increased risk of cavitation. To achieve the recommended inlet pressures with elevated temperatures, it is often necessary to use a booster pump. The booster pump should be approximately twice the system capacity to assure adequate flow into the pump. See chart on front page. REDUCTION IN RPM In addition to increasing the inlet pressure to the pump as temperature increases, reducing the pump rpm will also offer added protection. Reducing the rpm reduces the acceleration and vaporization of the water. Lower rpm reduces the risk of cavitation and its damaging effects. See chart on front for recommended rpm.INLET STABILIZER If more than 5-6 feet from the pump or long feed lines or a booster pump or high temperature are present, an inlet stabilizer should be installed to stabilize inlet pressure. Note: An inlet stabilizer will not function with a negative suction inlet. INCREASED LINE SIZE It is always important to have the inlet supply line sized to match or be one size larger than the pump inlet port for optimum performance, but it is most critical when the pumped liquid is at elevated temperatures. Under sizing the line will only compound the problems of high temperature vaporization. See individual pump data sheet. PROPERLY SIZED AND BAFFLED SUPPLY TANK The optimum installation for ambient temperature water requires a properly sized baffled supply tank. The tank should be enclosed and 6-10 times the system capacity with at least two baffles.

<ins>Introduction:</ins>
&nbsp;This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of 316SS manifold, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as DI water and salt water.&nbsp;
<ins>Technical Specifications:</ins>
Max Flow: 10 gpm / 37.9 lpm
Max Pressure: 2200
Inlet Port: Size3/4" NPT(F)
Discharge Port Size1/2" NPT(F)
RPM: 958
Drive Type(s): Belt, Clutch
Material316 Stainless Steel
<ins>Inlet Pressure v Water Temperature Vaporization and Caviation Analaysis</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:brgd3"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/mCAnnKkJMK3J3Qw6J5zc3x.jpg"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="brgd3" 
 layout="nodisplay"></amp-image-lightbox>

 
<ins> PRESSURIZED INLET </ins>
With ambient temperatures, piston pumps can handle a maximum negative suction of -8.5 psi (20 feet of water) and plunger pumps can handle a maximum negative suction -5 psi (11.5 feet of water). As the temperature of the water increases, the vapor pressure (pressure required to remain liquid) also increases. By increasing the inlet pressure to the pump, you can minimize the increased risk of cavitation. To achieve the recommended inlet pressures with elevated temperatures, it is often necessary to use a booster pump. The booster pump should be approximately twice the system capacity to assure adequate flow into the pump. See chart on front page. REDUCTION IN RPM In addition to increasing the inlet pressure to the pump as temperature increases, reducing the pump rpm will also offer added protection. Reducing the rpm reduces the acceleration and vaporization of the water. Lower rpm reduces the risk of cavitation and its damaging effects. See chart on front for recommended rpm.
<ins>INLET STABILIZER</ins>
&nbsp;If more than 5-6 feet from the pump or long feed lines or a booster pump or high temperature are present, an inlet stabilizer should be installed to stabilize inlet pressure. Note: An inlet stabilizer will not function with a negative suction inlet. INCREASED LINE SIZE It is always important to have the inlet supply line sized to match or be one size larger than the pump inlet port for optimum performance, but it is most critical when the pumped liquid is at elevated temperatures. Under sizing the line will only compound the problems of high temperature vaporization. See individual pump data sheet.&nbsp;
<ins>PROPERLY SIZED AND BAFFLED SUPPLY TANK</ins>&nbsp;
The optimum installation for ambient temperature water requires a properly sized baffled supply tank. The tank should be enclosed and 6-10 times the system capacity with at least two baffles.&nbsp;

Cat Pumps 1051 Service Manual

Cat Pumps 1051 Data Sheet

Ong Ming Jun Andre

Leader

Kranzle

Others

TSURUMI PUMP

Pressure Washers

Pumps Accessories

Lubricant Pumps

Rotating Piston Pumps

buyerIntroduction

Cat Pumps 15 Frame Plunger Reverse Osmosis Pump

cat pumps 15 frame plunger reverse osmosis pump pompa water air pam pumps/猫泵 框架柱塞反渗透泵 水泵 猫泵

cat-pumps-15-frame-plunger-reverse-osmosis-pump

 This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with nickel aluminum bronze manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings. 

 • Triplex design offers high-efficiency and low-pulsation. 

• Nickel Aluminum Bronze and 316 Stainless Steel models available to suit a range of high-salinity sea water or chemicals.

• 316 Stainless Steel is stronger and aids in corrosion resistance with aggressive liquids and sea water. • Belt-driven option provides precision flow setting.

• Compact direct-drive with bell housing and flexible coupler assembly.

• NEMA or IEC electric motor or SAE hydraulic options available. 

Alternative seal materials are available for higher temperature or chemical compatibility 

Drive Type(s): Belt, Clutch, Flexible Coupling and Bellhousing Material Nickel Aluminum Bronze 

Introduction: This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with nickel aluminum bronze manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings. Features: • Triplex design offers high-efficiency and low-pulsation. • Nickel Aluminum Bronze and 316 Stainless Steel models available to suit a range of high-salinity sea water or chemicals.• 316 Stainless Steel is stronger and aids in corrosion resistance with aggressive liquids and sea water. • Belt-driven option provides precision flow setting.• Compact direct-drive with bell housing and flexible coupler assembly.• NEMA or IEC electric motor or SAE hydraulic options available. • Pump comes standard with NBR seals. Alternative seal materials are available for higher temperature or chemical compatibility Technical SpecificationsMax Flow 3.5 gpm / 13.2 lpmMax Pressure 1500Inlet Port Size1/2&quot; NPT(F)Discharge Port Size3/8&quot; NPT(F)RPM1420Drive Type(s): Belt, Clutch, Flexible Coupling and Bellhousing Material Nickel Aluminum Bronze

<ins>Introduction:</ins>
&nbsp;This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with nickel aluminum bronze manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings.&nbsp;
&nbsp;<ins>Features:</ins>
&nbsp;• Triplex design offers high-efficiency and low-pulsation.&nbsp;
• Nickel Aluminum Bronze and 316 Stainless Steel models available to suit a range of high-salinity sea water or chemicals.
• 316 Stainless Steel is stronger and aids in corrosion resistance with aggressive liquids and sea water. • Belt-driven option provides precision flow setting.
• Compact direct-drive with bell housing and flexible coupler assembly.
• NEMA or IEC electric motor or SAE hydraulic options available.&nbsp;
• Pump comes standard with NBR seals.&nbsp;
Alternative seal materials are available for higher temperature or chemical compatibility&nbsp;
<ins>Technical Specifications</ins>
Max Flow 3.5 gpm / 13.2 lpm
Max Pressure 1500
Inlet Port Size1/2"
&nbsp;NPT(F)Discharge Port Size
3/8" NPT(F)RPM1420
Drive Type(s): Belt, Clutch, Flexible Coupling and Bellhousing Material Nickel Aluminum Bronze&nbsp;

277 Technical Data Sheet

Cat Pumps 3 Frame Plunger Pump

cat pumps frame plunger pump water pompa air pam pumps/猫泵 框架柱塞泵 水泵 猫泵

cat-pumps-3-frame-plunger-pump

This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with 316 stainless steel manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings.

• Triplex plunger design ensures high efficiency and low pulsation. 

• Durable high-pressure seals are lubricated and cooled by pumped liquid.

 • Preset low-pressure seals provide secondary protection against external leaks and require no packing adjustments.

 • Belt-driven option provides precision flow setting.

 • Direct-drive option offers a compact footprint for SAE hydraulic motors with a bell housing/flexible coupler assembly. 

• Model 2531C offers an external flush for high-temperature or lowlubricity liquids.

 • Pump comes standard with NBR seals. 

INTRODUCTION:This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with 316 stainless steel manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings. Technical Specifications Max Flow: 25 gpm / 94.6 lpmMax Pressure1200Inlet Port Size: 1 1/4&quot; NPT(F)Discharge Port Size: 3/4&quot; NPT(F)RPM: 1025Drive Type(s): Belt, ClutchMaterial: 316 Stainless Steel FEATURES • Triplex plunger design ensures high efficiency and low pulsation. • Durable high-pressure seals are lubricated and cooled by pumped liquid. • Preset low-pressure seals provide secondary protection against external leaks and require no packing adjustments. • Belt-driven option provides precision flow setting. • Direct-drive option offers a compact footprint for SAE hydraulic motors with a bell housing/flexible coupler assembly. • Model 2531C offers an external flush for high-temperature or lowlubricity liquids. • Pump comes standard with NBR seals. <figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/gmAwD25RWnO4TXyN9IwvZI.jpg" alt="" /><figcaption class="md-block-image-caption"></figcaption></figure>Alternative seal materials are available for higher temperature or chemical compatibility

&nbsp;
<ins>INTRODUCTION:</ins>
This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with 316 stainless steel manifolds, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings.

<ins>Technical Specifications</ins>
 
Max Flow: 25 gpm / 94.6 lpm
Max Pressure1200
Inlet Port Size: 1 1/4" NPT(F)
Discharge Port Size: 3/4" NPT(F)
RPM: 1025
Drive Type(s): Belt, Clutch
Material: 316 Stainless Steel

<ins>FEATURES </ins>
• Triplex plunger design ensures high efficiency and low pulsation.&nbsp;
• Durable high-pressure seals are lubricated and cooled by pumped liquid.
&nbsp;• Preset low-pressure seals provide secondary protection against external leaks and require no packing adjustments.
&nbsp;• Belt-driven option provides precision flow setting.
&nbsp;• Direct-drive option offers a compact footprint for SAE hydraulic motors with a bell housing/flexible coupler assembly.&nbsp;
• Model 2531C offers an external flush for high-temperature or lowlubricity liquids.
&nbsp;• Pump comes standard with NBR seals.&nbsp;

 <div class="img-ctnr">
 <amp-img 
 on="tap:2tepd"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/gmAwD25RWnO4TXyN9IwvZI.jpg"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="2tepd" 
 layout="nodisplay"></amp-image-lightbox>

 
Alternative seal materials are available for higher temperature or chemical compatibility&nbsp;

25 Plunger Pump Technical Data Sheet

25 PFR Plunger Pump Service Manual

Cat Pumps 25 Frame Plunger Pump 2531

cat pumps 25 frame plunger pump 2531 pompa rangka water air pam pumps/猫泵 框架柱塞泵 水泵 猫泵

cat-pumps-25-frame-plunger-pump-2531

This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of Stainless Steel manifolds, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as salt water.

Drive Type(s): Belt, Flexible Coupling and Bellhousing

 • Triplex design delivers high efficiency and low pulsation. 

• Durable dual V-Packings are lubricated and cooled by pumped liquid. 

• Pre-set Lo-pressure seals provide secondary protection against external leaks and require no packing adjustment.

• Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.

• Standard NBR seals with alternative options for temperature and chemical compatibility. 

Introduction: This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of Stainless Steel manifolds, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as salt water.Technical Specifications:Max Flow: 14 gpm / 53 lpmMax Pressure: 3000Inlet Port Size1 1/2&quot; NPT(F)Discharge Port Size 1&quot; NPT(F)RPM: 800Drive Type(s): Belt, Flexible Coupling and BellhousingMaterial: 316 Stainless Steel FEATURES: • Triplex design delivers high efficiency and low pulsation. • Durable dual V-Packings are lubricated and cooled by pumped liquid. • Pre-set Lo-pressure seals provide secondary protection against external leaks and require no packing adjustment.• Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.• Standard NBR seals with alternative options for temperature and chemical compatibility.

<ins>Introduction:</ins>&nbsp;
This is a triplex [three plunger rods] positive displacement, reciprocating, plunger pump, constructed of Stainless Steel manifolds, 316SS valve assemblies, solid ceramic plungers and standard NBR [Buna-N] seals and o-rings. These higher capacity plunger pumps are suitable for multi-gun and multi-nozzle, high pressure systems. and pumping special liquids such as salt water.
<ins>Technical Specifications:</ins>
Max Flow: 14 gpm / 53 lpm
Max Pressure: 3000
Inlet Port Size1 1/2" NPT(F)
Discharge Port Size 1" NPT(F)
RPM: 800
Drive Type(s): Belt, Flexible Coupling and Bellhousing
Material: 316 Stainless Steel&nbsp;
<ins> FEATURES:</ins>
&nbsp;• Triplex design delivers high efficiency and low pulsation.&nbsp;
• Durable dual V-Packings are lubricated and cooled by pumped liquid.&nbsp;
• Pre-set Lo-pressure seals provide secondary protection against external leaks and require no packing adjustment.
• Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.
• Standard NBR seals with alternative options for temperature and chemical compatibility.&nbsp;

CAT Pumps 3511 Technical Data Sheet

CAT Pumps 3511 Service Manual

Cat Pumps 35 Frame Plunger Pump 3511

cat pumps 35 frame plunger pump 3511 water pompa air pam pumps/猫泵 框架柱塞泵 水泵 猫泵

cat-pumps-35-frame-plunger-pump-3511

 This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with a 316 stainless steel inlet manifold, duplex stainless steel discharge manifold, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings. 

Drive Type(s)Belt, Flexible Coupling and Bellhousing

Introduction: This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with a 316 stainless steel inlet manifold, duplex stainless steel discharge manifold, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings. Technical Specifications: Max Flow40 gpm / 151.4 lpmMax Pressure2000Inlet Port Size1 1/2&quot; NPT(F)Discharge Port Size1&quot; NPT(F)RPM888Drive Type(s)Belt, Flexible Coupling and BellhousingMaterial316 Stainless Steel • Triplex design delivers high efficiency and low pulsation. • Durable dual V-Packings are lubricated and cooled by pumped liquid. • Pre-set Lo-pressure seals provide secondary protection against external leaks and require no packing adjustment.• Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.• Standard NBR seals with alternative options for temperature and chemical compatibility.

<ins>Introduction:</ins>&nbsp;
&nbsp;This triplex (three plunger rods) positive displacement, reciprocating plunger pump is constructed with a 316 stainless steel inlet manifold, duplex stainless steel discharge manifold, 316 stainless steel valve assemblies, solid ceramic plungers and standard NBR (Buna-N) seals and O-rings.&nbsp;
<ins>Technical Specifications:</ins>
&nbsp;Max Flow40 gpm / 151.4 lpm
Max Pressure2000
Inlet Port Size1 1/2" 
NPT(F)Discharge Port Size
1" NPT(F)RPM888
Drive Type(s)Belt, Flexible Coupling and Bellhousing
Material316 Stainless Steel&nbsp;
&nbsp;• Triplex design delivers high efficiency and low pulsation.&nbsp;
• Durable dual V-Packings are lubricated and cooled by pumped liquid.&nbsp;
• Pre-set Lo-pressure seals provide secondary protection against external leaks and require no packing adjustment.
• Special high-density, polished, concentric plungers provide a true wear surface and extended seal life.
• Standard NBR seals with alternative options for temperature and chemical compatibility.&nbsp;

3531 Data Sheet

35 Frame Stainless Steel Plunger Pump 3531DHS

35 frame stainless steel plunger pump 3531dhs pompa bingkai water pumps air cat pam keluli tahan karat pumps/猫泵 35框架不锈钢柱塞泵3531dhs 水泵 猫泵

35-frame-stainless-steel-plunger-pump-3531dhs

 Ingco MPP5511^ Foot Pump Max Pressure 150PSI

<h3 class="md-block-header-three"> Ingco MPP5511^ Foot Pump Max Pressure 150PSI</h3><ul class="md-block-unordered-list-item"><li>Size：φ55*120mm</li><li>Head fits Schrader, Presta，Dunlop</li><li>With Bar and PSI double units</li><li>High pressure durable hose 60cm</li><li>Steel cylinder and frame</li><li>Rubber pedal</li><li>Packed by color box</li></ul>

<h3>&nbsp;Ingco MPP5511^ Foot Pump Max Pressure 150PSI</h3>
<ul>
<li>Size：φ55*120mm</li>
<li>Head fits Schrader, Presta，Dunlop</li>
<li>With Bar and PSI double units</li>
<li>High pressure durable hose 60cm</li>
<li>Steel cylinder and frame</li>
<li>Rubber pedal</li>
<li>Packed by color box</li>
</ul>

Horme

Ingco MPP5511^ Foot Pump Max Pressure 150PSI

ingco mpp5511^ foot pump max pressure 150psi pompa kaki tekanan maksimum water pumps air maks pam ingco/英科 脚踏泵最大压力 水泵 英科

ingco-mpp5511-foot-pump-max-pressure-150psi

COMPACT, LIGHTWEIGHT AND PORTABLE. SINGLE-SPEED PUMPS DESIGNED TO DRIVE SINGLE-ACTING CYLINDERS.

■■ The power unit of choice for major manufacturers of auto body, frame straighteners and other shop equipment.

■■ Operate at 40-100 psi shop air pressure at the pump.

■■ Quiet operation that is suitable for indoor applications, 85 dBA at 10,000 psi.

■■ Serviceable pump motor is not a “throw away” providing economical repair.

■■ Internal relief valve protects circuit components, air inlet filter protects motor.

COMPACT, LIGHTWEIGHT AND PORTABLE. SINGLE-SPEED PUMPS DESIGNED TO DRIVE SINGLE-ACTING CYLINDERS.■■ The power unit of choice for major manufacturers of auto body, frame straighteners and other shop equipment.■■ Operate at 40-100 psi shop air pressure at the pump.■■ Quiet operation that is suitable for indoor applications, 85 dBA at 10,000 psi.■■ Serviceable pump motor is not a “throw away” providing economical repair.■■ Permanently vented reservoir cap.■■ Internal relief valve protects circuit components, air inlet filter protects motor.

COMPACT, LIGHTWEIGHT AND PORTABLE. SINGLE-SPEED PUMPS DESIGNED TO DRIVE SINGLE-ACTING CYLINDERS.
■■ The power unit of choice for major manufacturers of auto body, frame straighteners and other shop equipment.
■■ Operate at 40-100 psi shop air pressure at the pump.
■■ Quiet operation that is suitable for indoor applications, 85 dBA at 10,000 psi.
■■ Serviceable pump motor is not a “throw away” providing economical repair.
■■ Permanently vented reservoir cap.
■■ Internal relief valve protects circuit components, air inlet filter protects motor.

SPX Power Team Hyd. Hand Pumps Catalogue 

Tan Huang Chun

Power Team Air Pump, 3 - 8 Bar Air Supply

power team air pump, 8bar supply pompa udara tim tenaga, pasokan hand pumps tangan spx pam pasukan kuasa, bekalan team/spx 电源团队 空气泵，3 巴供气 手动泵

power-team-air-pump-3-8-bar-air-supply

Foot pedal lock and lightweight construction for portability

Two-speed operation reduces foot pedal strokes

arge foot-pad release valve for controlling load descent

Integral pressure relief valve for overload protection

Model : P392FP<ul class="md-block-unordered-list-item"><li>Robust, durable and compact</li><ul class="md-block-unordered-list-item"><li>Steel frame for maximum stability</li><li>Steel pumping handle</li><li>Aluminum reservoir</li></ul><li>Foot pedal lock and lightweight construction for portability</li><li>Two-speed operation reduces foot pedal strokes</li><li>arge foot-pad release valve for controlling load descent</li><li>Integral pressure relief valve for overload protection</li></ul>

Model : P392FP
<ul>
<li>Robust, durable and compact</li>
<ul>
<li>Steel frame for maximum stability</li>
<li>Steel pumping handle</li>
<li>Aluminum reservoir</li>
</ul>
<li>Foot pedal lock and lightweight construction for portability</li>
<li>Two-speed operation reduces foot pedal strokes</li>
<li>arge foot-pad release valve for controlling load descent</li>
<li>Integral pressure relief valve for overload protection</li>
</ul>

John Ng

Triangle

Optibelt

Nachi

KOYO

Kawasaki

Hydraulic Seals

Linear Bearing

Ball Bearings

Screw

Tap & Die Wrenches

Oil Seals

Pneumatic Accessories

Vee-Belts

Spherical Bearings 

Enerpac P392FP Lightweight Hydraulic Foot Pump

enerpac p392fp lightweight hydraulic foot pump pompa kaki hidraulik ringan pumps pam enerpac/恩派克 轻型液压脚踏泵 恩派克

enerpac-p392fp-lightweight-hydraulic-foot-pump

• Infinitely variable output pressure and flow

• Holds static pressure without generating heat or consuming power

• Standard models are suitable for oil or water applications

• Well proven and trouble-free operation

Max Rated Output Pressure: 23,695psi (1,634bar)

Air Motor: Anodised Aluminium / Nitrile (Buna-N) Seals

Piston: Stainless Steel + Corrosion Resistant Chrome Finish

L1** (standard): Brass / Copper Hydraulic Inlet, Air Inlet and Plated Steel Silencer

L2** (optional): Stainless Steel Hydraulic Inlet, Air Inlet and Silencer

/ F Panel mount digital stroke counter (non ATEX)

/ I (over all dimension varies) Isolation valve

/ M Mild steel painted frame (Painted Blue) + Stainless steel tank (if applicable to the unit)

/ O (over all dimension varies) Single pen chart recorder complete with recorder isolation valve

FEATURES• Infinitely variable output pressure and flow• Holds static pressure without generating heat or consuming power• Standard models are suitable for oil or water applications• Well proven and trouble-free operation• Designed for ease of maintenance• Low cost servicing• Robust construction PERFORMANCE DATAMax Rated Output Pressure: 23,695psi (1,634bar)Output Per Cycle: 4.5 in³ (74cc)Max Flow: 558 in³/min (9 litre/min)Max Air Supply Pressure: 100psi (7bar)Ratio: 236 : 1Air Consumption: 200 scfm (5,664 Nl/min) CONSTRUCTIONFrame: Stainless SteelAir Motor: Anodised Aluminium / Nitrile (Buna-N) SealsHydraulic Cylinder: Aluminium BronzePiston: Stainless Steel + Corrosion Resistant Chrome FinishOutlet Port: Stainless SteelL1** (standard): Brass / Copper Hydraulic Inlet, Air Inlet and Plated Steel SilencerL2** (optional): Stainless Steel Hydraulic Inlet, Air Inlet and Silencer CONNECTIONSHydraulic Inlet: 1/2&quot; NPT(F)Hydraulic Outlet: 9/16” HP(F)Air Inlet: 3/4” BSPP(F)Net Weight: 112kg (248lb) COMMON OPTIONS (BUT NOT LIMITED TO)/ A ATEX (94/9/EC) II 2GD c T5/ F Panel mount digital stroke counter (non ATEX)/ G Panel mount pneumatic stroke counter/ I (over all dimension varies) Isolation valve/ M Mild steel painted frame (Painted Blue) + Stainless steel tank (if applicable to the unit)/ O (over all dimension varies) Single pen chart recorder complete with recorder isolation valve/ R Relief valve/ W Fitted with wheels/ X Gauge protection guard

<ins>FEATURES</ins>
• Infinitely variable output pressure and flow
• Holds static pressure without generating heat or consuming power
• Standard models are suitable for oil or water applications
• Well proven and trouble-free operation
• Designed for ease of maintenance
• Low cost servicing
• Robust construction

<ins>PERFORMANCE DATA</ins>
Max Rated Output Pressure: 23,695psi (1,634bar)
Output Per Cycle: 4.5 in³ (74cc)
Max Flow: 558 in³/min (9 litre/min)
Max Air Supply Pressure: 100psi (7bar)
Ratio: 236 : 1
Air Consumption: 200 scfm (5,664 Nl/min)

<ins>CONSTRUCTION</ins>
Frame: Stainless Steel
Air Motor: Anodised Aluminium / Nitrile (Buna-N) Seals
Hydraulic Cylinder: Aluminium Bronze
Piston: Stainless Steel + Corrosion Resistant Chrome Finish
Outlet Port: Stainless Steel
L1** (standard): Brass / Copper Hydraulic Inlet, Air Inlet and Plated Steel Silencer
L2** (optional): Stainless Steel Hydraulic Inlet, Air Inlet and Silencer

<ins>CONNECTIONS</ins>
Hydraulic Inlet: 1/2" NPT(F)
Hydraulic Outlet: 9/16” HP(F)
Air Inlet: 3/4” BSPP(F)
Net Weight: 112kg (248lb)

<ins>COMMON OPTIONS (BUT NOT LIMITED TO)</ins>
/ A ATEX (94/9/EC) II 2GD c T5
/ F Panel mount digital stroke counter (non ATEX)
/ G Panel mount pneumatic stroke counter
/ I (over all dimension varies) Isolation valve
/ M Mild steel painted frame (Painted Blue) + Stainless steel tank (if applicable to the unit)
/ O (over all dimension varies) Single pen chart recorder complete with recorder isolation valve
/ R Relief valve
/ W Fitted with wheels
/ X Gauge protection guard

DHDA118 HPU Catalogue

Durajack

Kudos

Betex

JACKRAM

Atlas Copco

Hydraulic Jacks

Hydraulic Tools

Other Machines

Pressure Reducing Valve

Crimping & Stripping Pilers

Torque Wrenches

Other Electrical Accessories

Weight, Force & Pressure Gauges

Hydratron DHDA118 MK4.1 Hpu - 23.6KPSI - Nitrile - No Tank - Stainless Steel Frame - 9/16" Hp Outlet, Hydrotest Pump

hydratron dhda118 mk4.1 hpu 23.6kpsi nitrile tank stainless steel frame 9/16" hp outlet, hydrotest pump nitril tanpa tangki rangka baja tahan karat outlet hp, pompa uji hidro water pumps air tiada keluli alur keluar pam hidrotest 无水箱 不锈钢框架 出口，水压试验泵 水泵 海德拉顿

hydratron-dhda118-mk4-1-hpu-23-6kpsi-nitrile-no-tank-stainless-steel-frame-9-16-hp-outlet-hydrotest-pump

<ul class="md-block-unordered-list-item"><li> Engine Size: 163 cc </li><li>Horsepower: 4.8 hp (4 4/5 hp) </li><li>Tank Capacity: 3.28 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Aluminum </li><li>Seal Material: Buna N </li><li>Flow Rate @ 40 ft Head: 97 gpm </li><li>Flow Rate @ 60 ft Head: 89 gpm </li><li>Flow Rate @ 80 ft Head: 79 gpm </li><li>Maximum Head: 164 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Full Tubular Frame </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 71 psi </li><li>Inlet Size: 2 in NPT</li></ul>

<ul>
<li>&nbsp;Engine Size: 163 cc 
&nbsp;</li>
<li>Horsepower: 4.8 hp (4 4/5 hp) 
&nbsp;</li>
<li>Tank Capacity: 3.28 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Aluminum 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate @ 40 ft Head: 97 gpm 
&nbsp;</li>
<li>Flow Rate @ 60 ft Head: 89 gpm 
&nbsp;</li>
<li>Flow Rate @ 80 ft Head: 79 gpm 
&nbsp;</li>
<li>Maximum Head: 164 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Full Tubular Frame 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 71 psi 
&nbsp;</li>
<li>Inlet Size: 2 in NPT</li>
</ul>

Grainger

Dayton 11G231 Engine Driven Pump 163cc 1-1/2 Npt

dayton 11g231 engine driven pump 163cc 1-1/2 npt pompa bermesin water pumps air pam didorong enjin dayton/代顿 发动机驱动泵 水泵 代顿

dayton-11g231-engine-driven-pump-163cc-1-1-2-npt

Volute Material: Spheroid Graphite Ductile Iron (very durable and corrosion resistant)
 

<ul class="md-block-unordered-list-item"><li>Engine Size: 242 cc </li><li>Horsepower: 7.1 hp </li><li>Tank Capacity: 5.6 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Spheroid Graphite Ductile Iron (very durable and corrosion resistant) </li><li>Seal Material: Buna N </li><li>Flow Rate @ 40 ft Head: 290 gpm </li><li>Flow Rate @ 60 ft Head: 216 gpm </li><li>Flow Rate @ 80 ft Head: 112 gpm </li><li>Maximum Head: 92 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Full Tubular Frame </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 40 psi</li></ul>

<ul>
<li>Engine Size: 242 cc 
&nbsp;</li>
<li>Horsepower: 7.1 hp 
&nbsp;</li>
<li>Tank Capacity: 5.6 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Spheroid Graphite Ductile Iron (very durable and corrosion resistant) 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate @ 40 ft Head: 290 gpm 
&nbsp;</li>
<li>Flow Rate @ 60 ft Head: 216 gpm 
&nbsp;</li>
<li>Flow Rate @ 80 ft Head: 112 gpm 
&nbsp;</li>
<li>Maximum Head: 92 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Full Tubular Frame 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 40 psi</li>
</ul>

Dayton 11G236 Engine Driven Utility Pump 242cc 4 Npt

dayton 11g236 engine driven utility pump 242cc npt pompa utilitas bermesin water pumps air pam utiliti dipacu enjin dayton/代顿 发动机驱动多用途泵 水泵 代顿

dayton-11g236-engine-driven-utility-pump-242cc-4-npt

Volute Material: Spheroid Graphite Ductile Iron (strong and corrosion-resistant)
 

<ul class="md-block-unordered-list-item"><li> Engine Size: 163 cc </li><li>Horsepower: 4.8 hp </li><li>Tank Capacity: 3.28 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Spheroid Graphite Ductile Iron (strong and corrosion-resistant) </li><li>Seal Material: Buna N </li><li>Flow Rate @ 40 ft Head: 171 gpm </li><li>Flow Rate @ 60 ft Head: 115 gpm </li><li>Flow Rate @ 80 ft Head: 31 gpm </li><li>Maximum Head: 85 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Full Tubular Frame </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 37 psi</li></ul>

<ul>
<li>&nbsp;Engine Size: 163 cc 
&nbsp;</li>
<li>Horsepower: 4.8 hp 
&nbsp;</li>
<li>Tank Capacity: 3.28 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Spheroid Graphite Ductile Iron (strong and corrosion-resistant) 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate @ 40 ft Head: 171 gpm 
&nbsp;</li>
<li>Flow Rate @ 60 ft Head: 115 gpm 
&nbsp;</li>
<li>Flow Rate @ 80 ft Head: 31 gpm 
&nbsp;</li>
<li>Maximum Head: 85 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Full Tubular Frame 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 37 psi</li>
</ul>

Dayton 11G235 Engine Driven Utility Pump 163cc 3 Npt

dayton 11g235 engine driven utility pump 163cc npt pompa utilitas bermesin water pumps air pam utiliti dipacu enjin dayton/代顿 发动机驱动多用途泵 水泵 代顿

dayton-11g235-engine-driven-utility-pump-163cc-3-npt

Frame Design: Frame Rails with Top Handle
 

<ul class="md-block-unordered-list-item"><li> Engine Size: 25 cc </li><li>Horsepower: 1 hp </li><li>Tank Capacity: 0.58 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Aluminum </li><li>Seal Material: Buna N </li><li>Flow Rate at 40 ft Head: 23 gpm </li><li>Flow Rate at 60 ft Head: 19 gpm </li><li>Flow Rate at 80 ft Head: 13 gpm </li><li>Maximum Head: 106 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Frame Rails with Top Handle </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 47 psi </li><li>Inlet Size: 1 in NPT</li></ul>

<ul>
<li>&nbsp;Engine Size: 25 cc 
&nbsp;</li>
<li>Horsepower: 1 hp 
&nbsp;</li>
<li>Tank Capacity: 0.58 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Aluminum 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate at 40 ft Head: 23 gpm 
&nbsp;</li>
<li>Flow Rate at 60 ft Head: 19 gpm 
&nbsp;</li>
<li>Flow Rate at 80 ft Head: 13 gpm 
&nbsp;</li>
<li>Maximum Head: 106 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Frame Rails with Top Handle 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 47 psi 
&nbsp;</li>
<li>Inlet Size: 1 in NPT</li>
</ul>

Dayton 11G226 Engine Driven Utility Pump 25cc 1 Npt

dayton 11g226 engine driven utility pump 25cc npt pompa utilitas bermesin water pumps air pam utiliti dipacu enjin dayton/代顿 发动机驱动多用途泵 水泵 代顿

dayton-11g226-engine-driven-utility-pump-25cc-1-npt

<ul class="md-block-unordered-list-item"><li>Engine Size: 163 cc </li><li>Horsepower: 4.8 hp (4 4/5 hp) </li><li>Tank Capacity: 3.28 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Aluminum </li><li>Seal Material: Buna N </li><li>Flow Rate @ 40 ft Head: 99 gpm </li><li>Flow Rate @ 60 ft Head: 91 gpm </li><li>Flow Rate @ 80 ft Head: 78 gpm </li><li>Maximum Head: 187 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Full Tubular Frame </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 81 psi </li><li>Inlet Size: 2 in NPT </li><li>Discharge Size: 2 in NPT</li></ul>

<ul>
<li>Engine Size: 163 cc 
&nbsp;</li>
<li>Horsepower: 4.8 hp (4 4/5 hp) 
&nbsp;</li>
<li>Tank Capacity: 3.28 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Aluminum 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate @ 40 ft Head: 99 gpm 
&nbsp;</li>
<li>Flow Rate @ 60 ft Head: 91 gpm 
&nbsp;</li>
<li>Flow Rate @ 80 ft Head: 78 gpm 
&nbsp;</li>
<li>Maximum Head: 187 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Full Tubular Frame 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 81 psi 
&nbsp;</li>
<li>Inlet Size: 2 in NPT 
&nbsp;</li>
<li>Discharge Size: 2 in NPT</li>
</ul>

Dayton 11G232 Engine Driven Utility Pump 163cc 2 Npt

dayton 11g232 engine driven utility pump 163cc npt pompa utilitas bermesin water pumps air pam utiliti dipacu enjin dayton/代顿 发动机驱动多用途泵 水泵 代顿

dayton-11g232-engine-driven-utility-pump-163cc-2-npt

<ul class="md-block-unordered-list-item"><li> Engine Size: 163 cc </li><li>Horsepower: 4.8 hp (4 4/5 hp) </li><li>Tank Capacity: 3.28 qt </li><li>Ignition Type: Recoil-Start </li><li>Pump Mechanism: Centrifugal </li><li>Body Material: Aluminum </li><li>Volute Material: Cast Iron </li><li>Seal Material: Buna N </li><li>Flow Rate @ 40 ft Head: 213 gpm </li><li>Flow Rate @ 60 ft Head: 164 gpm </li><li>Flow Rate @ 80 ft Head: 91 gpm </li><li>Maximum Head: 85 ft </li><li>Maximum Suction Lift: 26 ft </li><li>Frame Design: Full Tubular Frame </li><li>Impeller Design: Semi-Open </li><li>Maximum Discharge Pressure: 37 psi </li><li>Inlet Size: 3 in NPT </li><li>Discharge Size: 3 in NPT</li></ul>

<ul>
<li>&nbsp;Engine Size: 163 cc 
&nbsp;</li>
<li>Horsepower: 4.8 hp (4 4/5 hp) 
&nbsp;</li>
<li>Tank Capacity: 3.28 qt 
&nbsp;</li>
<li>Ignition Type: Recoil-Start 
&nbsp;</li>
<li>Pump Mechanism: Centrifugal 
&nbsp;</li>
<li>Body Material: Aluminum 
&nbsp;</li>
<li>Volute Material: Cast Iron 
&nbsp;</li>
<li>Seal Material: Buna N 
&nbsp;</li>
<li>Flow Rate @ 40 ft Head: 213 gpm 
&nbsp;</li>
<li>Flow Rate @ 60 ft Head: 164 gpm 
&nbsp;</li>
<li>Flow Rate @ 80 ft Head: 91 gpm 
&nbsp;</li>
<li>Maximum Head: 85 ft 
&nbsp;</li>
<li>Maximum Suction Lift: 26 ft 
&nbsp;</li>
<li>Frame Design: Full Tubular Frame 
&nbsp;</li>
<li>Impeller Design: Semi-Open 
&nbsp;</li>
<li>Maximum Discharge Pressure: 37 psi 
&nbsp;</li>
<li>Inlet Size: 3 in NPT 
&nbsp;</li>
<li>Discharge Size: 3 in NPT</li>
</ul>