Adhesive

adhesive

Epoxy

epoxy

Ppg 1090 Sigmashield High Build Phenolic Epoxy (Grey) Pack Size 15,71 Litres

PPG SigmaShield 1090 is a two component, flint reinforced, solvent free, polyamine cured, epoxy compound, suitable for the protection of both steel and concrete. This product provides protection against water, mild chemicals, impact, and corrosion.

PPG SigmaShield 1090 is a product ideal for use in the marine environment that can be exposed to water just 30 minutes after application. 1090 provides a water permeable layer that allows trapped moisture to be released all the while allowing the surface to breathe, making it highly suited for use on decks regularly exposed to water.

PPG SigmaShield 1090 is a heavy substance that can be applied using a flat trowel or using spray application, however the product must be transported from the container with mixed material to the spray gun. After 6-8 hours the surface is dry to touch and can be recoated after a minimum of 6 hours.

Sigma SigmaShield 1090 is suitable for use on dock-side appliances and surfaces and is highly resistance to abrasion and impact. The marine environment is constantly exposed to varying conditions and 1090 offers the utmost protection and adhesion in dry or wet conditions, warm or cold. SigmaShield 1090 should primarily be used on steel and concrete substrates situated in the marine environment.

<h3 class="md-block-header-three">Ppg 1090 Sigmashield High Build Phenolic Epoxy (Grey) Pack Size 15,71 Litres</h3>PPG SigmaShield 1090 is a two component, flint reinforced, solvent free, polyamine cured, epoxy compound, suitable for the protection of both steel and concrete. This product provides protection against water, mild chemicals, impact, and corrosion.<ul class="md-block-unordered-list-item"><li>Best Uses</li></ul>PPG SigmaShield 1090 is a product ideal for use in the marine environment that can be exposed to water just 30 minutes after application. 1090 provides a water permeable layer that allows trapped moisture to be released all the while allowing the surface to breathe, making it highly suited for use on decks regularly exposed to water.<ul class="md-block-unordered-list-item"><li>Application</li></ul>PPG SigmaShield 1090 is a heavy substance that can be applied using a flat trowel or using spray application, however the product must be transported from the container with mixed material to the spray gun. After 6-8 hours the surface is dry to touch and can be recoated after a minimum of 6 hours.<ul class="md-block-unordered-list-item"><li>Surface and Environment</li></ul>Sigma SigmaShield 1090 is suitable for use on dock-side appliances and surfaces and is highly resistance to abrasion and impact. The marine environment is constantly exposed to varying conditions and 1090 offers the utmost protection and adhesion in dry or wet conditions, warm or cold. SigmaShield 1090 should primarily be used on steel and concrete substrates situated in the marine environment.

<h3>Ppg 1090 Sigmashield High Build Phenolic Epoxy (Grey) Pack Size 15,71 Litres</h3>
PPG SigmaShield 1090 is a two component, flint reinforced, solvent free, polyamine cured, epoxy compound, suitable for the protection of both steel and concrete. This product provides protection against water, mild chemicals, impact, and corrosion.
<ul>
<li>Best Uses</li>
</ul>
PPG SigmaShield 1090 is a product ideal for use in the marine environment that can be exposed to water just 30 minutes after application. 1090 provides a water permeable layer that allows trapped moisture to be released all the while allowing the surface to breathe, making it highly suited for use on decks regularly exposed to water.
<ul>
<li>Application</li>
</ul>
PPG SigmaShield 1090 is a heavy substance that can be applied using a flat trowel or using spray application, however the product must be transported from the container with mixed material to the spray gun. After 6-8 hours the surface is dry to touch and can be recoated after a minimum of 6 hours.
<ul>
<li>Surface and Environment</li>
</ul>
Sigma SigmaShield 1090 is suitable for use on dock-side appliances and surfaces and is highly resistance to abrasion and impact. The marine environment is constantly exposed to varying conditions and 1090 offers the utmost protection and adhesion in dry or wet conditions, warm or cold. SigmaShield 1090 should primarily be used on steel and concrete substrates situated in the marine environment.

Product Datasheet

Safety Datasheet

eezee

Ppg 1090 Sigmashield High Build Phenolic Epoxy (grey) Pack Size 15,71 Litres

ppg 1090 sigmashield high build phenolic epoxy (grey) pack size 15,71 litres (abu-abu) ukuran kemasan liter epoksi (kelabu) saiz pek 15.71 高强度酚醛环氧树脂（灰色）包装规格：15.71 环氧胶

ppg-1090-sigmashield-high-build-phenolic-epoxy-grey-pack-size-15-71-litres

Ppg 230 Sigmatherm Epoxy Phenolic up to Dry Temp 200 or 300degC (Pink, Grey) Pack Size 20 Litres

PPG SigmaTherm 230 is a two component high build heat resistant phenolic epoxy coating designed for use under insulation systems to provide heat protection of up to 230°C.

SigmaTherm 230 is a high performance, heat resistant product that provides protection to a variety of metal substrates. PPG SigmaTherm 230 is ideally suited for application to pipes, radiators and low heat engines to aid the protection of the surface and surrounding area.

Blast clean steel to ISO-Sa2.5 with a blasting profile of 40 - 70 microns. The substrate must be perfectly dry before and during application. Degrease stainless steel with solvents and sweep blast. The temperature of the mixed base and hardener should be above 15°C otherwise extra thinner may be required. Adding to much thinner results in reduced sag resistance. Allow sufficient induction time as per data sheet.

SigmaTherm 230 is a high performance product that provides surfaces with a high glossy finish to aid protection and offer a level of decoration with an aluminium effect. SigmaTherm 230 should ideally be used internally to offer heat resistance to appliances of up to 230°C.

<h3 class="md-block-header-three">Ppg 230 Sigmatherm Epoxy Phenolic up to Dry Temp 200 or 300degC (Pink, Grey) Pack Size 20 Litres</h3><ul class="md-block-unordered-list-item"><li>Product Details</li></ul>PPG SigmaTherm 230 is a two component high build heat resistant phenolic epoxy coating designed for use under insulation systems to provide heat protection of up to 230°C.<ul class="md-block-unordered-list-item"><li>Best Uses</li></ul>SigmaTherm 230 is a high performance, heat resistant product that provides protection to a variety of metal substrates. PPG SigmaTherm 230 is ideally suited for application to pipes, radiators and low heat engines to aid the protection of the surface and surrounding area.<ul class="md-block-unordered-list-item"><li>Application</li></ul>Blast clean steel to ISO-Sa2.5 with a blasting profile of 40 - 70 microns. The substrate must be perfectly dry before and during application. Degrease stainless steel with solvents and sweep blast. The temperature of the mixed base and hardener should be above 15°C otherwise extra thinner may be required. Adding to much thinner results in reduced sag resistance. Allow sufficient induction time as per data sheet.<ul class="md-block-unordered-list-item"><li>Surface and Environment</li></ul>SigmaTherm 230 is a high performance product that provides surfaces with a high glossy finish to aid protection and offer a level of decoration with an aluminium effect. SigmaTherm 230 should ideally be used internally to offer heat resistance to appliances of up to 230°C.

<h3>Ppg 230 Sigmatherm Epoxy Phenolic up to Dry Temp 200 or 300degC (Pink, Grey) Pack Size 20 Litres</h3>
<ul>
<li>Product Details</li>
</ul>
PPG SigmaTherm 230 is a two component high build heat resistant phenolic epoxy coating designed for use under insulation systems to provide heat protection of up to 230°C.
<ul>
<li>Best Uses</li>
</ul>
SigmaTherm 230 is a high performance, heat resistant product that provides protection to a variety of metal substrates. PPG SigmaTherm 230 is ideally suited for application to pipes, radiators and low heat engines to aid the protection of the surface and surrounding area.
<ul>
<li>Application</li>
</ul>
Blast clean steel to ISO-Sa2.5 with a blasting profile of 40 - 70 microns. The substrate must be perfectly dry before and during application. Degrease stainless steel with solvents and sweep blast. The temperature of the mixed base and hardener should be above 15°C otherwise extra thinner may be required. Adding to much thinner results in reduced sag resistance. Allow sufficient induction time as per data sheet.
<ul>
<li>Surface and Environment</li>
</ul>
SigmaTherm 230 is a high performance product that provides surfaces with a high glossy finish to aid protection and offer a level of decoration with an aluminium effect. SigmaTherm 230 should ideally be used internally to offer heat resistance to appliances of up to 230°C.

Ppg 230 Sigmatherm Epoxy Phenolic up to Dry Temp 200 or 300degC (pink, Grey) Pack Size 20 Litres

ppg 230 sigmatherm epoxy phenolic dry temp 200 300degc (pink, grey) pack size 20 litres hingga suhu kering atau 300 derajat celcius (merah muda, abu-abu) ukuran kemasan liter epoksi sehingga jambu, kelabu) saiz pek 环氧酚醛树脂，干燥温度高达 摄氏度（粉色、灰色）包装规格 环氧胶