Mechanical Parts

mechanical-parts

O Ring

o-ring

Silicone O-Rings are sometimes referred to VMQ O-Rings.

Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility. 

In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.

Overview on Application Rating for Material Silicone 

Heat Ozone & Aging Resistance - Excellent

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING AS568 AS038ID 66.40 X CS 1.78Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/FCzQeVVZcBI1YR3_hCz1WI.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS038
ID 66.40 X CS 1.78
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:1u0pt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/FCzQeVVZcBI1YR3_hCz1WI.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="1u0pt" 
 layout="nodisplay"></amp-image-lightbox>

John

Others

Optibelt

Gates

SAMTECH

VITON

V Rings

Rubber Seals

Oil Seals

Shaft Couplings

Plumbing Tools & Equipment

Ball Bearings

Hydraulic Seals

Wall Plugs, Anchors, Fixings & Kits

Vee-Belts

buyerIntroduction

ORING AS568 AS038 ID 66.40 X CS 1.78 Silicone 70 Shore

oring as568 as038 id 66.40 cs 1.78 silicone 70 shore ring o-ring oem gelang oem/oem代工 1.78硅胶70肖氏 o型圈 oem代工

oring-as568-as038-id-66-40-x-cs-1-78-silicone-70-shore

ORING AS568 AS411 ID 66.04 X CS 6.99Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/lo9PEYliivuZrCFoAC_EM8.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS411
&nbsp;ID 66.04 X CS 6.99
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:14m1i"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/lo9PEYliivuZrCFoAC_EM8.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="14m1i" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS410 ID 66.04 X CS 6.99 Silicone 70 Shore

oring as568 as410 id 66.04 cs 6.99 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 6.99硅胶70肖氏 o型圈 oem代工

oring-as568-as410-id-66-04-x-cs-6-99-silicone-70-shore

ORING AS568 AS471 ID 557.66 X CS 6.99Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/4GIQKCjUZqAyalqt7tGRmj.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS471
&nbsp;ID 557.66 X CS 6.99
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bca99"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/4GIQKCjUZqAyalqt7tGRmj.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bca99" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS471 ID 557.66 X CS 6.99 Silicone 70 Shore

oring as568 as471 id 557.66 cs 6.99 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 6.99硅胶70肖氏 o型圈 oem代工

oring-as568-as471-id-557-66-x-cs-6-99-silicone-70-shore

ORING AS568 AS146 ID 66.34 X CS 2.62Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/mfze6Uuz7L8ZQAGinK1DML.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS146
&nbsp;ID 66.34 X CS 2.62
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bhgq6"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/mfze6Uuz7L8ZQAGinK1DML.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bhgq6" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS146 ID 66.34 X CS 2.62 Silicone 70 Shore

oring as568 as146 id 66.34 cs 2.62 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 2.62硅胶70肖氏 o型圈 oem代工

oring-as568-as146-id-66-34-x-cs-2-62-silicone-70-shore

ORING AS568 AS386 ID 430.66 x CS 5.33Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS386
&nbsp;ID 430.66 x CS 5.33
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:vggt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="vggt" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS386 ID 430.66 x CS 5.33 Silicone 70 Shore

oring as568 as386 id 430.66 cs 5.33 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 5.33硅胶70肖氏 o型圈 oem代工

oring-as568-as386-id-430-66-x-cs-5-33-silicone-70-shore

ORING AS568 AS231 ID 66.27 x CS 3.53Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS231
&nbsp;ID 66.27 x CS 3.53
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:vggt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="vggt" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS231 ID 66.27 x CS 3.53 Silicone 70 Shore

oring as568 as231 id 66.27 cs 3.53 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.53硅胶70肖氏 o型圈 oem代工

oring-as568-as231-id-66-27-x-cs-3-53-silicone-70-shore

ORING AS568 AS334 ID 66.04 x CS 5.33Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS334
&nbsp;ID 66.04 x CS 5.33
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:vggt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="vggt" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS334 ID 66.04 x CS 5.33 Silicone 70 Shore

oring as568 as334 id 66.04 cs 5.33 silicone 70 shore 66,04 silikon ring o-ring oem gelang oem/oem代工 5.33硅胶70肖氏 o型圈 oem代工

oring-as568-as334-id-66-04-x-cs-5-33-silicone-70-shore

ORING AS568 AS463 ID 430.66 X CS 6.99Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/5wf4cABuZ7JE20mQ6a20rz.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS463
&nbsp;ID 430.66 X CS 6.99
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:eu5vl"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/5wf4cABuZ7JE20mQ6a20rz.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="eu5vl" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS463 ID 430.66 X CS 6.99 Silicone 70 Shore

oring as568 as463 id 430.66 cs 6.99 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 6.99硅胶70肖氏 o型圈 oem代工

oring-as568-as463-id-430-66-x-cs-6-99-silicone-70-shore

ORING AS568 AS377 ID 253.06 x CS 5.33Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS377&nbsp;
ID 253.06 x CS 5.33
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:vggt"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/CQtu68rj2BdnXOTJY~KCRV.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="vggt" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS377 ID 253.06 x CS 5.33 Silicone 70 Shore

oring as568 as377 id 253.06 cs 5.33 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 5.33硅胶70肖氏 o型圈 oem代工

oring-as568-as377-id-253-06-x-cs-5-33-silicone-70-shore

ORING AS568 AS441 ID 177.17 X CS 6.99 Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/OcVdPpnfhI5BZEiYVq4Dom.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS441
&nbsp;ID 177.17 X CS 6.99&nbsp;
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:6cqm6"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/OcVdPpnfhI5BZEiYVq4Dom.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="6cqm6" 
 layout="nodisplay"></amp-image-lightbox>

Oring AS568 AS441 Id 177.17 X Cs 6.99 Silicone 70 Shore

oring as568 as441 id 177.17 cs 6.99 silicone 70 shore ring o-ring oem gelang oem/oem代工 6.99硅胶70肖氏 o型圈 oem代工

oring-as568-as441-id-177-17-x-cs-6-99-silicone-70-shore

ORING AS568 AS420 ID 97.79 X CS 6.99Material : Silicone 70 Shore Additional InformationSilicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/g3DjD7AnzreVPZGed4RIWj.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS420
&nbsp;ID 97.79 X CS 6.99
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
<ins>Additional Information</ins>
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:dgvr3"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/g3DjD7AnzreVPZGed4RIWj.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="dgvr3" 
 layout="nodisplay"></amp-image-lightbox>