RFS Hydraulics

Plumbing & Sanitary

plumbing-sanitary

Ferrule Fittings

ferrule-fittings

Pipe Tee

pipe-tee

Rfs Brass 12mm Od X 12mm Od X 12mm Od Union Tee Compression Fittings, Light Series F-D-B-T-12L

Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation.  To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union tee is a T-shaped fitting with three ports. It connects tubes and pipes to the main line at a 90 degree angle with three compression ends. 

Series	: L (Light Series) & S (Heavy Series)

Working Pressure (bar)	: L series (160-315) & S series (315-800)

Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1

Step 1: Cutting ring and nut to be placed over the tube in the correct direction.

Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.

Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.

Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.

Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3 class="md-block-header-three">Rfs Brass 12mm Od X 12mm Od X 12mm Od Union Tee Compression Fittings, Light Series F-D-B-T-12L</h3>Union TEECompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union tee is a T-shaped fitting with three ports. It connects tubes and pipes to the main line at a 90 degree angle with three compression ends. About Union TeeSize	: 6mm to 42mmSeries	: L (Light Series) &amp; S (Heavy Series)Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)Material	: BrassMaterial Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1DIN Fittings installation guidelines:Step 1: Cutting ring and nut to be placed over the tube in the correct direction.Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 12mm Od X 12mm Od X 12mm Od Union Tee Compression Fittings, Light Series F-D-B-T-12L</h3>
Union TEE
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union tee is a T-shaped fitting with three ports. It connects tubes and pipes to the main line at a 90 degree angle with three compression ends.&nbsp;
About Union Tee
Size	: 6mm to 42mm
Series	: L (Light Series) &amp; S (Heavy Series)
Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)
Material	: Brass
Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1
DIN Fittings installation guidelines:
Step 1: Cutting ring and nut to be placed over the tube in the correct direction.
Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.
Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.
Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.
Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

AF Hydro

Oleo Tecnica

BOTHWELL

LAME

Stauff

Others

MJ Technos

LY Metal

Flanges

Pipe Clamps

Pipe Coupling

Pipe Adaptor

Pipe Elbow

Pipe Nipple

Camlock Fittings

Copper Tubing

Kelvin How

buyerIntroduction

Rfs Brass 12mm Od X 12mm Od X 12mm Od Union Tee Compression Fittings, Light Series

rfs brass 12mm od union tee compression fittings, light series kuningan seri ringan f-d-b-t-12l pipe pipa hydraulics loyang kelengkapan mampatan tee, siri paip hydraulics/rfs 液压 黄铜 联合三通压缩接头，轻型系列

rfs-brass-12mm-od-x-12mm-od-x-12mm-od-union-tee-compression-fittings-light-series

Specification Sheet

Rfs Brass Compression Tube Fitting Ferrule, 12MM Od , Union Tee With Double Ferrule

rfs brass compression tube fitting ferrule, 12mm od union tee double ferrule pemasangan tabung kompresi kuningan rfs, 12mm, dengan ganda fittings hydraulics tiub mampatan loyang kesatuan berganda hyupshin/协信 黄铜压缩管接头套圈，12mm 外径，带双套圈的联合三通 液压

rfs-brass-compression-tube-fitting-ferrule-12mm-od-union-tee-with-double-ferrule

RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee 3/4 Male Ends F-J-S-T-12

RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee, 3/4 Male Ends, T Shaped Adapter Connector for Tubes and Hoses, 37-Degree Flared Compression Fitting, Sae J514 Standard F-J-S-T-12

JIC fittings are manufactured in compliance with ISO 8434-2 and SAE J514 standards. JIC is also known as flared fittings as it has 37-degree flared seating, which is different from NPT thread. JIC is applied with the assembly of hoses, used to connect various tube sizes with sleeve and nut. A complete set of JIC fittings includes sleeve, nut and bodyIt is suitable to be applied in general application where the fluid is conveyed under high pressure such as hydraulics or industrial.  Fitting sizes are designed according to outer diameter of tubes and to be used to connect various types of tube ends. JIC fittings with NPT thread are able withstand higher pressure, temperature, and resistance than NPT thread.  Depending on the type and size of fitting, the maximum working pressure is up to 6200 PSI (430 Bars). There are also several connection types; Type 1: JIC (1st connection) x JIC (2nd connection), Type 2: JIC (1st connection) x BSPP (2nd connection), and Type 3: JIC (1st connection) x NPT (2nd connection).JIC fittings are available in either stainless steel, carbon steel or brass material. The JIC fitting made from stainless steel 316 grade is with higher resistance against corrosion and rust, and it can withstand temperature between ​-60 °C to 200 °C.

Usage: Connect tubes and hoses from three direction 

Material: Stainless steel 316 with higher resistance against corrosion

Working temperature: ​-60 °C to 200 °C

Working pressure: Depending on the type and size of fitting, can withstand up to 6200 PSI

Cut the tube to the required length and flare the end to 37-degree before installation.

Lubricate the threads and the surface of the flare.

Insert the nut and sleeve onto the tube end connection. Align the components and turn the flare nut until the sealing surface is fully contacted.

<h3 class="md-block-header-three">RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee 3/4 Male Ends F-J-S-T-12</h3>RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee, 3/4 Male Ends, T Shaped Adapter Connector for Tubes and Hoses, 37-Degree Flared Compression Fitting, Sae J514 Standard F-J-S-T-12JIC – UNION TEE WHAT IS JIC FITTING?JIC fittings are manufactured in compliance with ISO 8434-2 and SAE J514 standards. JIC is also known as flared fittings as it has 37-degree flared seating, which is different from NPT thread. JIC is applied with the assembly of hoses, used to connect various tube sizes with sleeve and nut. A complete set of JIC fittings includes sleeve, nut and bodyIt is suitable to be applied in general application where the fluid is conveyed under high pressure such as hydraulics or industrial. Fitting sizes are designed according to outer diameter of tubes and to be used to connect various types of tube ends. JIC fittings with NPT thread are able withstand higher pressure, temperature, and resistance than NPT thread. Depending on the type and size of fitting, the maximum working pressure is up to 6200 PSI (430 Bars). There are also several connection types; Type 1: JIC (1st connection) x JIC (2nd connection), Type 2: JIC (1st connection) x BSPP (2nd connection), and Type 3: JIC (1st connection) x NPT (2nd connection).JIC fittings are available in either stainless steel, carbon steel or brass material. The JIC fitting made from stainless steel 316 grade is with higher resistance against corrosion and rust, and it can withstand temperature between ​-60 °C to 200 °C.About JIC – UNION TEE<ul class="md-block-unordered-list-item"><li>Usage: Connect tubes and hoses from three direction </li><li>Thread: JIC Male on three ends </li><li>Material: Stainless steel 316 with higher resistance against corrosion</li><li>Size range: ¼” – 2”</li><li>Working temperature: ​-60 °C to 200 °C</li><li>Working pressure: Depending on the type and size of fitting, can withstand up to 6200 PSI</li></ul>STEPS TO INSTALL JIC FITTINGS <ol class="md-block-ordered-list-item"><li>Cut the tube to the required length and flare the end to 37-degree before installation.</li><li>Lubricate the threads and the surface of the flare.</li><li>Insert the nut and sleeve onto the tube end connection. Align the components and turn the flare nut until the sealing surface is fully contacted.</li></ol>

<h3>RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee 3/4 Male Ends F-J-S-T-12</h3>
RFS Hydraulics Rfs Stainless Steel SS316 Jic Union Tee, 3/4 Male Ends, T Shaped Adapter Connector for Tubes and Hoses, 37-Degree Flared Compression Fitting, Sae J514 Standard F-J-S-T-12
JIC – UNION TEE 
WHAT IS JIC FITTING?
JIC fittings are manufactured in compliance with ISO 8434-2 and SAE J514 standards. JIC is also known as flared fittings as it has 37-degree flared seating, which is different from NPT thread. JIC is applied with the assembly of hoses, used to connect various tube sizes with sleeve and nut. A complete set of JIC fittings includes sleeve, nut and bodyIt is suitable to be applied in general application where the fluid is conveyed under high pressure such as hydraulics or industrial. Fitting sizes are designed according to outer diameter of tubes and to be used to connect various types of tube ends. JIC fittings with NPT thread are able withstand higher pressure, temperature, and resistance than NPT thread. Depending on the type and size of fitting, the maximum working pressure is up to 6200 PSI (430 Bars). There are also several connection types; Type 1: JIC (1st connection) x JIC (2nd connection), Type 2: JIC (1st connection) x BSPP (2nd connection), and Type 3: JIC (1st connection) x NPT (2nd connection).JIC fittings are available in either stainless steel, carbon steel or brass material. The JIC fitting made from stainless steel 316 grade is with higher resistance against corrosion and rust, and it can withstand temperature between ​-60 °C to 200 °C.
About JIC – UNION TEE
<ul>
<li>Usage: Connect tubes and hoses from three direction&nbsp;</li>
<li>Thread: JIC Male on three ends&nbsp;</li>
<li>Material: Stainless steel 316 with higher resistance against corrosion</li>
<li>Size range: ¼” – 2”</li>
<li>Working temperature: ​-60 °C to 200 °C</li>
<li>Working pressure: Depending on the type and size of fitting, can withstand up to 6200 PSI</li>
</ul>
STEPS TO INSTALL JIC FITTINGS&nbsp;
<ol>
<li>Cut the tube to the required length and flare the end to 37-degree before installation.</li>
<li>Lubricate the threads and the surface of the flare.</li>
<li>Insert the nut and sleeve onto the tube end connection. Align the components and turn the flare nut until the sealing surface is fully contacted.</li>
</ol>
&nbsp;

Rfs Stainless Steel SS316 Jic Union Tee, 3/4" Male Ends, T Shaped Adapter Connector for Tubes and Hoses, 37-Degree Flared Compression Fitting, Sae J514 Standard

rfs stainless steel ss316 jic union tee, 3/4" male ends, shaped adapter connector tubes hoses, 37-degree flared compression fitting, sae j514 standard hidraulik tee 3/4 pria berakhir f-j-s-t-12 pipe pipa hydraulics keluli tahan karat hujung lelaki paip hydraulics/rfs 液压 不锈钢 联合三通 外螺纹端 ends

rfs-stainless-steel-ss316-jic-union-tee-3-4-male-ends-t-shaped-adapter-connector-for-tubes-and-hoses-37-degree-flared-compression-fitting-sae-j514-standard