RS Pro

Mechanical Parts

mechanical-parts

O Ring

o-ring

Nitrile is often referred to Buna (Buna-N) and NBR.

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C). 

It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.

However Nitrile are not a restricting factors in many applications.

Overview on Application Rating for Material Nitrile (NBR) 

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING JIS B2401 P145 ID 144.60 x CS 5.70Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/_O~cEOrdxc9kN4gkTcDrvz.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P145
&nbsp;ID 144.60 x CS 5.70
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bngab"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/_O~cEOrdxc9kN4gkTcDrvz.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bngab" 
 layout="nodisplay"></amp-image-lightbox>

John

Others

Optibelt

Gates

SAMTECH

VITON

V Rings

Rubber Seals

Oil Seals

Shaft Couplings

Plumbing Tools & Equipment

Ball Bearings

Hydraulic Seals

Wall Plugs, Anchors, Fixings & Kits

Vee-Belts

buyerIntroduction

ORING JIS B2401 P145 ID 144.60 x CS 5.70 Nitrile (NBR) 70 Shore

oring jis b2401 p145 id 144.60 cs 5.70 nitrile (nbr) 70 shore 144,60 5,70 ring o-ring oem gelang oem/oem代工 5.70腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p145-id-144-60-x-cs-5-70-nitrile-nbr-70-shore

ORING JIS B2401 P145 ID 144.60 x CS 5.70Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/bddd4GmCYttMWoAq8oDEJw.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P145
&nbsp;ID 144.60 x CS 5.70
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:2mv6b"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/bddd4GmCYttMWoAq8oDEJw.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="2mv6b" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P145 ID 144.60 x CS 5.70 Nitrile (NBR) 90 Shore

oring jis b2401 p145 id 144.60 cs 5.70 nitrile (nbr) 90 shore 144,60 5,70 ring o-ring oem gelang oem/oem代工 5.70腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p145-id-144-60-x-cs-5-70-nitrile-nbr-90-shore

ORING JIS B2401 G145 ID 144.40 x CS 3.10Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/DWjz8dPSxPSNnLQ24gk5CD.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G145
&nbsp;ID 144.40 x CS 3.10
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:bnaog"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/DWjz8dPSxPSNnLQ24gk5CD.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="bnaog" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 G145 ID 144.40 x CS 3.10 Nitrile (NBR) 90 Shore

oring jis b2401 g145 id 144.40 cs 3.10 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 3.10丁腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-g145-id-144-40-x-cs-3-10-nitrile-nbr-90-shore

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).  

Overview on Application Rating for Material Nitrile (NBR)  

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.  

Applications that require resistance to OIL 

Applications that are required to work in low temperatures (-0°C) 

High performance Fuel systems that requires strictly no leakage

Covering 	and lubricating the threading of the shaft 

ORING AS568 AS145 ID 64.77 X CS 2.62Material : Nitrile (NBR) 70 ShoreAdditional InformationNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Primary UsageO-Rings and rubber seals are generally used for:<ul class="md-block-unordered-list-item"><li>Applications that require resistance to OIL </li><li>Applications that are required to work in low temperatures (-0°C) </li><li>High performance Fuel systems that requires strictly no leakage</li><ul class="md-block-unordered-list-item"><li>Aircrafts </li><li>Marine Ships </li><li>F1 Cars</li></ul><li>General Industrial Use </li></ul>Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:<ul class="md-block-unordered-list-item"><li>Covering 	and lubricating the threading of the shaft </li></ul>The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.<ul class="md-block-unordered-list-item"><li>Don’t force it over sharp corners </li></ul>That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.<ul class="md-block-unordered-list-item"><li>Even stretching </li></ul>You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.<ul class="md-block-unordered-list-item"><li>Don’t roll it down the shaft </li></ul>Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.<ul class="md-block-unordered-list-item"><li>Finishing 	it off </li></ul>Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/BTM1iWZFU5nvtQ9d6ul~dI.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS145
&nbsp;ID 64.77 X CS 2.62
Material : Nitrile (NBR) 70 Shore
<ins>Additional Information</ins>
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>&nbsp;
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.&nbsp;&nbsp;
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
<ul>
<li>Applications that require resistance to OIL&nbsp;</li>
<li>Applications that are required to work in low temperatures (-0°C)&nbsp;</li>
<li>High performance Fuel systems that requires strictly no leakage</li>
<ul>
<li>Aircrafts&nbsp;</li>
<li>Marine Ships&nbsp;</li>
<li>F1 Cars</li>
</ul>
<li>General Industrial Use&nbsp;&nbsp;&nbsp;</li>
</ul>
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
<ul>
<li>Covering 	and lubricating the threading of the shaft&nbsp;</li>
</ul>
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
<ul>
<li>Don’t force it over sharp corners&nbsp;</li>
</ul>
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
<ul>
<li>Even stretching&nbsp;</li>
</ul>
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
<ul>
<li>Don’t roll it down the shaft&nbsp;</li>
</ul>
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
<ul>
<li>Finishing 	it off&nbsp;</li>
</ul>
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:d4lso"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/BTM1iWZFU5nvtQ9d6ul~dI.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="d4lso" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS145 ID 64.77 X CS 2.62 Nitrile (NBR) 70 Shore

oring as568 as145 id 64.77 cs 2.62 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 2.62腈（nbr）70肖氏 o型圈 oem代工

oring-as568-as145-id-64-77-x-cs-2-62-nitrile-nbr-70-shore

ORING AS568 AS145 ID 64.77 X CS 2.62Material : Nitrile (NBR) 90 Shore Additional InformationNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Primary UsageO-Rings and rubber seals are generally used for:<ul class="md-block-unordered-list-item"><li>Applications that require resistance to OIL </li><li>Applications that are required to work in low temperatures (-0°C) </li><li>High performance Fuel systems that requires strictly no leakage</li><ul class="md-block-unordered-list-item"><li>Aircrafts </li><li>Marine Ships </li><li>F1 Cars</li></ul><li>General Industrial Use </li></ul>Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:<ul class="md-block-unordered-list-item"><li>Covering 	and lubricating the threading of the shaft </li></ul>The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.<ul class="md-block-unordered-list-item"><li>Don’t force it over sharp corners </li></ul>That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.<ul class="md-block-unordered-list-item"><li>Even stretching </li></ul>You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.<ul class="md-block-unordered-list-item"><li>Don’t roll it down the shaft </li></ul>Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.<ul class="md-block-unordered-list-item"><li>Finishing 	it off </li></ul>Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/dmMy8go98xri9~Owp09FBu.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS145
&nbsp;ID 64.77 X CS 2.62
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
<ins>Additional Information</ins>
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>&nbsp;
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.&nbsp;&nbsp;
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
<ul>
<li>Applications that require resistance to OIL&nbsp;</li>
<li>Applications that are required to work in low temperatures (-0°C)&nbsp;</li>
<li>High performance Fuel systems that requires strictly no leakage</li>
<ul>
<li>Aircrafts&nbsp;</li>
<li>Marine Ships&nbsp;</li>
<li>F1 Cars</li>
</ul>
<li>General Industrial Use&nbsp;&nbsp;&nbsp;</li>
</ul>
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
<ul>
<li>Covering 	and lubricating the threading of the shaft&nbsp;</li>
</ul>
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
<ul>
<li>Don’t force it over sharp corners&nbsp;</li>
</ul>
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
<ul>
<li>Even stretching&nbsp;</li>
</ul>
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
<ul>
<li>Don’t roll it down the shaft&nbsp;</li>
</ul>
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
<ul>
<li>Finishing 	it off&nbsp;</li>
</ul>
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:1ghr9"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/dmMy8go98xri9~Owp09FBu.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="1ghr9" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS145 ID 64.77 X CS 2.62 Nitrile (NBR) 90 Shore

oring as568 as145 id 64.77 cs 2.62 nitrile (nbr) 90 shore ring o-ring oem gelang oem/oem代工 2.62腈（nbr）90肖氏 o型圈 oem代工

oring-as568-as145-id-64-77-x-cs-2-62-nitrile-nbr-90-shore

RS PRO Datasheet

RS PRO O-Rings Overview

PHOENIX CONTACT

Mag-Lite

Facom

Wago

Kimberly Clark

HEICO

Screw

Plugs & Connector 

Panel Mount Indicators 

Clamps

Indicator Lights

Ethernet Cable

Drill Bits & Drill Bit Sets

Bolts

Electrical Wire 

Fuses & Fusegear

RS Components ETH SG

Rs Pro 2556978 Nitrile O-Ring, 145mm Bore, 149mm Outer Diameter (1 Bag of 5)

rs pro 2556978 nitrile o-ring, 145mm bore, 149mm outer diameter (1 bag 5) nitril lubang 145mm, luar kantong isi ring o-ring cincin nitril, bor beg gelang 丁腈 形圈，145mm 内径，149mm 外径（1 个） o型圈 rs专业版

rs-pro-2556978-nitrile-o-ring-145mm-bore-149mm-outer-diameter-1-bag-of-5

O-Rings, rubber seals and custom molded rubber components for:

· Specialized Fuel systems, automotive, marine, and aircraft

Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.

When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.

The following steps should help in installing an O-ring correctly and saving time as well:

1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.

2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.

3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.

4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.

5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.

Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 G144 ID 140.40 x CS 3.10Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings, rubber seals and custom molded rubber components for:· Standard Oil resistant applications· Custom Low temperature applications· Specialized Fuel systems, automotive, marine, and aircraft· General Industrial UseImportant Tips When Installing an O-RingProper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.Installing an O-RingWhen installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.Tips for Better Installation of O-RingsThe following steps should help in installing an O-ring correctly and saving time as well:1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 G144&nbsp;
ID 140.40 x CS 3.10
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings, rubber seals and custom molded rubber components for:
· Standard Oil resistant applications
· Custom Low temperature applications
· Specialized Fuel systems, automotive, marine, and aircraft
· General Industrial Use
<ins>Important Tips When Installing an O-Ring</ins>
Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.
Installing an O-Ring
When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.
Tips for Better Installation of O-Rings
The following steps should help in installing an O-ring correctly and saving time as well:
1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.
2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.
3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.
4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.
5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.
Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 G145 ID 144.40 x CS 3.10 Nitrile (NBR) 70 Shore

oring jis b2401 g145 id 144.40 cs 3.10 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.10腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-g145-id-144-40-x-cs-3-10-nitrile-nbr-70-shore

Rs Pro 2556856 Nitrile O-Ring, 145mm Bore, 157mm Outer Diameter (1 Bag of 2)

rs pro 2556856 nitrile o-ring, 145mm bore, 157mm outer diameter (1 bag 2) nitril lubang 145mm, luar kantong isi ring o-ring cincin nitril, bor beg gelang 丁腈 形圈，145mm 内径，157mm 外径（1 个） o型圈 rs专业版

rs-pro-2556856-nitrile-o-ring-145mm-bore-157mm-outer-diameter-1-bag-of-2

Rs Pro 1965180 Nitrile Rubber O-Ring, 145mm Bore, 155mm Outer Diameter (1 Bag of 5)

rs pro 1965180 nitrile rubber o-ring, 145mm bore, 155mm outer diameter (1 bag 5) o-ring karet nitrile, lubang 145mm, luar kantong isi ring cincin getah nitril, bor beg gelang 丁腈橡胶 形圈，145mm 内径，155mm 外径（1 个） o型圈 rs专业版

rs-pro-1965180-nitrile-rubber-o-ring-145mm-bore-155mm-outer-diameter-1-bag-of-5

Rs Pro 2556979 Nitrile O-Ring, 145mm Bore, 152mm Outer Diameter (1 Bag of 5)

rs pro 2556979 nitrile o-ring, 145mm bore, 152mm outer diameter (1 bag 5) nitril lubang 145mm, luar kantong isi ring o-ring cincin nitril, bor beg gelang 丁腈 形圈，145mm 内径，152mm 外径（1 个） o型圈 rs专业版

rs-pro-2556979-nitrile-o-ring-145mm-bore-152mm-outer-diameter-1-bag-of-5

Rs Pro 2556961 Nitrile O-Ring, 135mm Bore, 145mm Outer Diameter (1 Bag of 5)

rs pro 2556961 nitrile o-ring, 135mm bore, 145mm outer diameter (1 bag 5) nitril lubang 135mm, luar kantong isi ring o-ring cincin nitril, bor beg gelang 丁腈 形圈，135mm 内径，145mm 外径（1 个） o型圈 rs专业版

rs-pro-2556961-nitrile-o-ring-135mm-bore-145mm-outer-diameter-1-bag-of-5

Rs Pro 1965003 Nitrile Rubber O-Ring, 140mm Bore, 145mm Outer Diameter (1 Bag of 5)

rs pro 1965003 nitrile rubber o-ring, 140mm bore, 145mm outer diameter (1 bag 5) luar 140mm, kantong isi ring o-ring cincin getah nitril, bor beg gelang 丁腈橡胶 形圈，140mm 内径，145mm 外径（1 个） o型圈 rs专业版

rs-pro-1965003-nitrile-rubber-o-ring-140mm-bore-145mm-outer-diameter-1-bag-of-5

Rs Pro 2556977 Nitrile O-Ring, 145mm Bore, 150mm Outer Diameter (1 Bag of 5)

rs pro 2556977 nitrile o-ring, 145mm bore, 150mm outer diameter (1 bag 5) nitril lubang 145mm, luar kantong isi ring o-ring cincin nitril, bor beg gelang 丁腈 形圈，145mm 内径，150mm 外径（1 个） o型圈 rs专业版