Electricals

electricals

Contactors

contactors

Mechanical Parts

mechanical-parts

O Ring

o-ring

Nitrile is often referred to Buna (Buna-N) and NBR.

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C). 

It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.

However Nitrile are not a restricting factors in many applications.

Overview on Application Rating for Material Nitrile (NBR) 

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING JIS B2401 P24 ID 23.70 x CS 3.50Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/wjkIhfeBJSwhBwNvVFCuv~.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P24&nbsp;
ID 23.70 x CS 3.50
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:f7hkq"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/wjkIhfeBJSwhBwNvVFCuv~.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="f7hkq" 
 layout="nodisplay"></amp-image-lightbox>

John

Others

Optibelt

Gates

SAMTECH

VITON

V Rings

Rubber Seals

Oil Seals

Shaft Couplings

Plumbing Tools & Equipment

Ball Bearings

Hydraulic Seals

Wall Plugs, Anchors, Fixings & Kits

Vee-Belts

buyerIntroduction

ORING JIS B2401 P24 ID 23.70 x CS 3.50 Nitrile (NBR) 70 Shore

oring jis b2401 p24 id 23.70 cs 3.50 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.50腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p24-id-23-70-x-cs-3-50-nitrile-nbr-70-shore

ORING JIS B2401 P25 ID 24.70 x CS 3.50Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/i5SSBGBm670QtcF45dTfE5.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P25&nbsp;
ID 24.70 x CS 3.50
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:4tvvb"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/i5SSBGBm670QtcF45dTfE5.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="4tvvb" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P25 ID 24.70 x CS 3.50 Nitrile (NBR) 70 Shore

oring jis b2401 p25 id 24.70 cs 3.50 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.50腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p25-id-24-70-x-cs-3-50-nitrile-nbr-70-shore

ORING JIS B2401 P24 ID 23.70 x CS 3.50Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/vHBkNNCDa4gd3uXbSZbQn~.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P24
&nbsp;ID 23.70 x CS 3.50
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:6auum"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/vHBkNNCDa4gd3uXbSZbQn~.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="6auum" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P24 ID 23.70 x CS 3.50 Nitrile (NBR) 90 Shore

oring jis b2401 p24 id 23.70 cs 3.50 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 3.50腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p24-id-23-70-x-cs-3-50-nitrile-nbr-90-shore

Abb AF52-30-11-13 Contactor 3P 22KW 1NO 1NC 50/60HZ 100-250VAC/DC

Catalog Description:AF52-30-11-13 100-250V50/60HZ-DC Contactor

Long Description:The AF52-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 22 kW / 400 V AC (AC-3) or 40 hp / 480 V UL and switching power circuits up to 100 A (AC-1) or 80 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.

Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-1, UL 60947-4-1, CSA C22.2 No. 60947-1:22, CSA C22.2 No. 60947-4-1:22

Rated Operational Voltage:Auxiliary Circuit 690 V

Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz

Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 105 A

Rated Operational Current AC-1 (Ie):(690 V) 40 °C 100 A

Rated Operational Current AC-3 (Ie):(415 V) 60 °C 53 A

Rated Operational Current AC-3e (Ie):(415 V) 60 °C 53 A

Rated Operational Power AC-3 (Pe):(400 V) 22 kW

Rated Operational Power AC-3e (Pe):(415 V) 30 kW

Rated Operational Current AC-15 (Ie):(500 V) 2 A

Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 600 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 110 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 250 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 1000 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 350 A

Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 440 V 950 A

cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 690 V 600 A

Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour

Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A

Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A

<h3 class="md-block-header-three">Abb AF52-30-11-13 Contactor 3P 22KW 1NO 1NC 50/60HZ 100-250VAC/DC</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:AF52-30-11-13</li><li>Product ID:1SBL367001R1311</li><li>EAN:3471523132436</li><li>Catalog Description:AF52-30-11-13 100-250V50/60HZ-DC Contactor</li><li>Long Description:The AF52-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 22 kW / 400 V AC (AC-3) or 40 hp / 480 V UL and switching power circuits up to 100 A (AC-1) or 80 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li><li>Number of Main Contacts NO:3</li><li>Number of Main Contacts NC:0</li><li>Number of Auxiliary Contacts NO:1</li><li>Number of Auxiliary Contacts NC:1</li><li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-1, UL 60947-4-1, CSA C22.2 No. 60947-1:22, CSA C22.2 No. 60947-4-1:22</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V</li><li>Main Circuit 690 V</li><li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li><li>Control Circuit 50 / 60 Hz</li><li>Main Circuit 50 / 60 Hz</li><li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 105 A</li><li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li><li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 100 A</li><li>(690 V) 60 °C 80 A</li><li>(690 V) 70 °C 70 A</li><li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 53 A</li><li>(440 V) 60 °C 53 A</li><li>(500 V) 60 °C 45 A</li><li>(690 V) 60 °C 35 A</li><li>(380 / 400 V) 60 °C 53 A</li><li>(220 / 230 / 240 V) 60 °C 53 A</li><li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 53 A</li><li>(440 V) 60 °C 53 A</li><li>(500 V) 60 °C 45 A</li><li>(690 V) 60 °C 35 A</li><li>(380 / 400 V) 60 °C 53 A</li><li>(220 / 230 / 240 V) 60 °C 53 A</li><li>Rated Operational Power AC-3 (Pe):(400 V) 22 kW</li><li>(415 V) 30 kW</li><li>(440 V) 30 kW</li><li>(500 V) 30 kW</li><li>(690 V) 30 kW</li><li>(380 / 400 V) 22 kW</li><li>(220 / 230 / 240 V) 15 kW</li><li>Rated Operational Power AC-3e (Pe):(415 V) 30 kW</li><li>(440 V) 30 kW</li><li>(500 V) 30 kW</li><li>(690 V) 30 kW</li><li>(380 / 400 V) 22 kW</li><li>(220 / 230 / 240 V) 15 kW</li><li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li><li>(690 V) 2 A</li><li>(24 / 127 V) 6 A</li><li>(220 / 240 V) 4 A</li><li>(400 / 440 V) 3 A</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 600 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 110 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 250 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 1000 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 350 A</li><li>for 0.1 s 140 A</li><li>for 1 s 100 A</li><li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 950 A</li><li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 600 A</li><li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li><li>(AC-15) 1200 cycles per hour</li><li>(AC-2 / AC-4) 150 cycles per hour</li><li>(AC-3) 1200 cycles per hour</li><li>(DC-13) 900 cycles per hour</li><li>Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li><li>(110 V) 2 Poles in Series, 60 °C 80 A</li><li>(110 V) 2 Poles in Series, 70 °C 70 A</li><li>(110 V) 3 Poles in Series, 40 °C 100 A</li><li>(110 V) 3 Poles in Series, 60 °C 80 A</li><li>(110 V) 3 Poles in Series, 70 °C 70 A</li><li>(220 V) 3 Poles in Series, 40 °C 100 A</li><li>(220 V) 3 Poles in Series, 60 °C 80 A</li><li>(220 V) 3 Poles in Series, 70 °C 70 A</li><li>(72 V) 1-Pole, 40 °C 100 A</li><li>(72 V) 1-Pole, 60 °C 80 A</li><li>(72 V) 1-Pole, 70 °C 70 A</li><li>(72 V) 2 Poles in Series, 40 °C 100 A</li><li>(72 V) 2 Poles in Series, 60 °C 80 A</li><li>(72 V) 2 Poles in Series, 70 °C 70 A</li><li>(72 V) 3 Poles in Series, 40 °C 100 A</li><li>(72 V) 3 Poles in Series, 60 °C 80 A</li><li>(72 V) 3 Poles in Series, 70 °C 70 A</li><li>Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li><li>(110 V) 2 Poles in Series, 60 °C 80 A</li><li>(110 V) 2 Poles in Series, 70 °C 70 A</li><li>(110 V) 3 Poles in Series, 40 °C 100 A</li><li>(110 V) 3 Poles in Series, 60 °C 80 A</li><li>(110 V) 3 Poles in Series, 70 °C 70 A</li><li>(220 V) 3 Poles in Series, 40 °C 100 A</li><li>(220 V) 3 Poles in Series, 60 °C 80 A</li><li>(220 V) 3 Poles in Series, 70 °C 70 A</li><li>(72 V) 1-Pole, 40 °C 100 A</li><li>(72 V) 1-Pole, 60 °C 80 A</li><li>(72 V) 1-Pole, 70 °C 70 A</li><li>(72 V) 2 Poles in Series, 40 °C 100 A</li><li>(72 V) 2 Poles in Series, 60 °C 80 A</li><li>(72 V) 2 Poles in Series, 70 °C 70 A</li><li>(72 V) 3 Poles in Series, 40 °C 100 A</li><li>(72 V) 3 Poles in Series, 60 °C 80 A</li><li>(72 V) 3 Poles in Series, 70 °C 70 A</li><li>Rated Operational Current DC-5 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li><li>(110 V) 2 Poles in Series, 60 °C 80 A</li><li>(110 V) 2 Poles in Series, 70 °C 70 A</li><li>(110 V) 3 Poles in Series, 40 °C 100 A</li><li>(110 V) 3 Poles in Series, 60 °C 80 A</li><li>(110 V) 3 Poles in Series, 70 °C 70 A</li><li>(220 V) 3 Poles in Series, 40 °C 100 A</li><li>(220 V) 3 Poles in Series, 60 °C 80 A</li><li>(220 V) 3 Poles in Series, 70 °C 70 A</li><li>(72 V) 1-Pole, 40 °C 100 A</li><li>(72 V) 1-Pole, 60 °C 80 A</li><li>(72 V) 1-Pole, 70 °C 70 A</li><li>(72 V) 2 Poles in Series, 40 °C 100 A</li><li>(72 V) 2 Poles in Series, 60 °C 80 A</li><li>(72 V) 2 Poles in Series, 70 °C 70 A</li><li>(72 V) 3 Poles in Series, 40 °C 100 A</li><li>(72 V) 3 Poles in Series, 60 °C 80 A</li><li>(72 V) 3 Poles in Series, 70 °C 70 A</li><li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li><li>(48 V) 2.8 A / 134 W</li><li>(72 V) 1 A / 72 W</li><li>(110 V) 0.55 A / 60 W</li><li>(125 V) 0.55 A / 69 W</li><li>(220 V) 0.27 A / 60 W</li><li>(250 V) 0.27 A / 68 W</li><li>(400 V) 0.15 A / 60 W</li><li>(500 V) 0.13 A / 65 W</li><li>(600 V) 0.1 A / 60 W</li><li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li><li>acc. to IEC 60947-5-1 690 V</li><li>acc. to UL/CSA 600 V</li><li>Rated Impulse Withstand Voltage (Uimp):6 kV</li><li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li><li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li><li>60 Hz 100 ... 250 V</li><li>DC Operation 100 ... 250 V</li><li>Coil Consumption:Average Holding Value 50 / 60 Hz 4 V·A</li><li>Average Holding Value 50 Hz 4 V·A</li><li>Average Holding Value 60 Hz 4 V·A</li><li>Average Holding Value DC 2 W</li><li>Average Holding Value, from Warm State 2 W</li><li>Operate Time:Between Coil De-energization and NC Contact Closing 19 ... 105 ms</li><li>Between Coil De-energization and NO Contact Opening 17 ... 100 ms</li><li>Between Coil Energization and NC Contact Opening 38 ... 95 ms</li><li>Between Coil Energization and NO Contact Closing 42 ... 100 ms</li><li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li><li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li><li>Mounting by Screws (not supplied):2 x M4 or 2 x M6 screws placed diagonally</li><li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 4 ... 35 mm²</li><li>Flexible with Insulated Ferrule 1/2x 4 ... 35 mm²</li><li>Rigid Stranded 1/2x 6 ... 35 mm²</li><li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Rigid 1/2x 1 ... 2.5 mm²</li><li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Wire Stripping Length:Auxiliary Circuit 10 mm</li><li>Control Circuit 10 mm</li><li>Main Circuit 16 mm</li><li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP10</li><li>Terminal Type:Screw Terminals</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb AF52-30-11-13 Contactor 3P 22KW 1NO 1NC 50/60HZ 100-250VAC/DC</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:AF52-30-11-13</li>
<li>Product ID:1SBL367001R1311</li>
<li>EAN:3471523132436</li>
<li>Catalog Description:AF52-30-11-13 100-250V50/60HZ-DC Contactor</li>
<li>Long Description:The AF52-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 22 kW / 400 V AC (AC-3) or 40 hp / 480 V UL and switching power circuits up to 100 A (AC-1) or 80 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li>
<li>Number of Main Contacts NO:3</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:1</li>
<li>Number of Auxiliary Contacts NC:1</li>
<li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-1, UL 60947-4-1, CSA C22.2 No. 60947-1:22, CSA C22.2 No. 60947-4-1:22</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V</li>
<li>Main Circuit 690 V</li>
<li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li>
<li>Control Circuit 50 / 60 Hz</li>
<li>Main Circuit 50 / 60 Hz</li>
<li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 105 A</li>
<li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li>
<li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 100 A</li>
<li>(690 V) 60 °C 80 A</li>
<li>(690 V) 70 °C 70 A</li>
<li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 53 A</li>
<li>(440 V) 60 °C 53 A</li>
<li>(500 V) 60 °C 45 A</li>
<li>(690 V) 60 °C 35 A</li>
<li>(380 / 400 V) 60 °C 53 A</li>
<li>(220 / 230 / 240 V) 60 °C 53 A</li>
<li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 53 A</li>
<li>(440 V) 60 °C 53 A</li>
<li>(500 V) 60 °C 45 A</li>
<li>(690 V) 60 °C 35 A</li>
<li>(380 / 400 V) 60 °C 53 A</li>
<li>(220 / 230 / 240 V) 60 °C 53 A</li>
<li>Rated Operational Power AC-3 (Pe):(400 V) 22 kW</li>
<li>(415 V) 30 kW</li>
<li>(440 V) 30 kW</li>
<li>(500 V) 30 kW</li>
<li>(690 V) 30 kW</li>
<li>(380 / 400 V) 22 kW</li>
<li>(220 / 230 / 240 V) 15 kW</li>
<li>Rated Operational Power AC-3e (Pe):(415 V) 30 kW</li>
<li>(440 V) 30 kW</li>
<li>(500 V) 30 kW</li>
<li>(690 V) 30 kW</li>
<li>(380 / 400 V) 22 kW</li>
<li>(220 / 230 / 240 V) 15 kW</li>
<li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li>
<li>(690 V) 2 A</li>
<li>(24 / 127 V) 6 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(400 / 440 V) 3 A</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 600 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 110 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 250 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 1000 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 350 A</li>
<li>for 0.1 s 140 A</li>
<li>for 1 s 100 A</li>
<li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 950 A</li>
<li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 600 A</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li>
<li>(AC-15) 1200 cycles per hour</li>
<li>(AC-2 / AC-4) 150 cycles per hour</li>
<li>(AC-3) 1200 cycles per hour</li>
<li>(DC-13) 900 cycles per hour</li>
<li>Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 1-Pole, 40 °C 100 A</li>
<li>(72 V) 1-Pole, 60 °C 80 A</li>
<li>(72 V) 1-Pole, 70 °C 70 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 70 A</li>
<li>Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 1-Pole, 40 °C 100 A</li>
<li>(72 V) 1-Pole, 60 °C 80 A</li>
<li>(72 V) 1-Pole, 70 °C 70 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 70 A</li>
<li>Rated Operational Current DC-5 (Ie):(110 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 1-Pole, 40 °C 100 A</li>
<li>(72 V) 1-Pole, 60 °C 80 A</li>
<li>(72 V) 1-Pole, 70 °C 70 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 70 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 100 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 70 A</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li>
<li>(48 V) 2.8 A / 134 W</li>
<li>(72 V) 1 A / 72 W</li>
<li>(110 V) 0.55 A / 60 W</li>
<li>(125 V) 0.55 A / 69 W</li>
<li>(220 V) 0.27 A / 60 W</li>
<li>(250 V) 0.27 A / 68 W</li>
<li>(400 V) 0.15 A / 60 W</li>
<li>(500 V) 0.13 A / 65 W</li>
<li>(600 V) 0.1 A / 60 W</li>
<li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li>
<li>acc. to IEC 60947-5-1 690 V</li>
<li>acc. to UL/CSA 600 V</li>
<li>Rated Impulse Withstand Voltage (Uimp):6 kV</li>
<li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li>
<li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li>
<li>60 Hz 100 ... 250 V</li>
<li>DC Operation 100 ... 250 V</li>
<li>Coil Consumption:Average Holding Value 50 / 60 Hz 4 V·A</li>
<li>Average Holding Value 50 Hz 4 V·A</li>
<li>Average Holding Value 60 Hz 4 V·A</li>
<li>Average Holding Value DC 2 W</li>
<li>Average Holding Value, from Warm State 2 W</li>
<li>Operate Time:Between Coil De-energization and NC Contact Closing 19 ... 105 ms</li>
<li>Between Coil De-energization and NO Contact Opening 17 ... 100 ms</li>
<li>Between Coil Energization and NC Contact Opening 38 ... 95 ms</li>
<li>Between Coil Energization and NO Contact Closing 42 ... 100 ms</li>
<li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li>
<li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li>
<li>Mounting by Screws (not supplied):2 x M4 or 2 x M6 screws placed diagonally</li>
<li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 4 ... 35 mm²</li>
<li>Flexible with Insulated Ferrule 1/2x 4 ... 35 mm²</li>
<li>Rigid Stranded 1/2x 6 ... 35 mm²</li>
<li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Rigid 1/2x 1 ... 2.5 mm²</li>
<li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Wire Stripping Length:Auxiliary Circuit 10 mm</li>
<li>Control Circuit 10 mm</li>
<li>Main Circuit 16 mm</li>
<li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP10</li>
<li>Terminal Type:Screw Terminals</li>
<li>Unit of Measurement : Pcs</li>
</ul>

Jimmy Foo

SCHNEIDER ELECTRIC

Philips

Thomas & Betts

BRADY

Bussmann

Weidmuller

FUJI

Crouse-Hinds

Circuit Breaker

Fuses & Fusegear

Plugs & Connector 

Light Bulbs

Led Lights

Junction & Enclosure Box

Other Electrical Accessories

Light Tubes

Doreen Tan

abb af52-30-11-13 contactor 3p 22kw 1no 1nc 50/60hz 100-250vac/dc kontaktor contactors para kontraktor penyentuh penghubung 接触器

abb-af52-30-11-13-contactor-3p-22kw-1no-1nc-50-60hz-100-250vac-dc

Abb AF65-30-11-13 Contactor 3P 30KW 1NO 1NC 50/60HZ 100-250VAC/DC

Catalog Description:AF65-30-11-13 100-250V50/60HZ-DC Contactor

Long Description:The AF65-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 30 kW / 400 V AC (AC-3) or 50 hp / 480 V UL and switching power circuits up to 105 A (AC-1) or 90 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.

Rated Operational Current AC-1 (Ie):(690 V) 40 °C 105 A

Rated Operational Current AC-3 (Ie):(415 V) 60 °C 65 A

Rated Operational Current AC-3e (Ie):(415 V) 60 °C 65 A

Rated Operational Power AC-3 (Pe):(400 V) 30 kW

Rated Operational Power AC-3e (Pe):(415 V) 37 kW

Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A

Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A

<h3 class="md-block-header-three">Abb AF65-30-11-13 Contactor 3P 30KW 1NO 1NC 50/60HZ 100-250VAC/DC</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:AF65-30-11-13</li><li>Product ID:1SBL387001R1311</li><li>EAN:3471523132733</li><li>Catalog Description:AF65-30-11-13 100-250V50/60HZ-DC Contactor</li><li>Long Description:The AF65-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 30 kW / 400 V AC (AC-3) or 50 hp / 480 V UL and switching power circuits up to 105 A (AC-1) or 90 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li><li>Number of Main Contacts NO:3</li><li>Number of Main Contacts NC:0</li><li>Number of Auxiliary Contacts NO:1</li><li>Number of Auxiliary Contacts NC:1</li><li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-1, UL 60947-4-1, CSA C22.2 No. 60947-1:22, CSA C22.2 No. 60947-4-1:22</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V</li><li>Main Circuit 690 V</li><li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li><li>Control Circuit 50 / 60 Hz</li><li>Main Circuit 50 / 60 Hz</li><li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 105 A</li><li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li><li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 105 A</li><li>(690 V) 60 °C 90 A</li><li>(690 V) 70 °C 80 A</li><li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 65 A</li><li>(440 V) 60 °C 65 A</li><li>(500 V) 60 °C 55 A</li><li>(690 V) 60 °C 39 A</li><li>(380 / 400 V) 60 °C 65 A</li><li>(220 / 230 / 240 V) 60 °C 65 A</li><li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 65 A</li><li>(440 V) 60 °C 65 A</li><li>(500 V) 60 °C 55 A</li><li>(690 V) 60 °C 39 A</li><li>(380 / 400 V) 60 °C 65 A</li><li>(220 / 230 / 240 V) 60 °C 65 A</li><li>Rated Operational Power AC-3 (Pe):(400 V) 30 kW</li><li>(415 V) 37 kW</li><li>(440 V) 37 kW</li><li>(500 V) 37 kW</li><li>(690 V) 37 kW</li><li>(380 / 400 V) 30 kW</li><li>(220 / 230 / 240 V) 18.5 kW</li><li>Rated Operational Power AC-3e (Pe):(415 V) 37 kW</li><li>(440 V) 37 kW</li><li>(500 V) 37 kW</li><li>(690 V) 37 kW</li><li>(380 / 400 V) 30 kW</li><li>(220 / 230 / 240 V) 18.5 kW</li><li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li><li>(690 V) 2 A</li><li>(24 / 127 V) 6 A</li><li>(220 / 240 V) 4 A</li><li>(400 / 440 V) 3 A</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 600 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 110 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 250 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 1000 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 350 A</li><li>for 0.1 s 140 A</li><li>for 1 s 100 A</li><li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 950 A</li><li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 600 A</li><li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li><li>(AC-15) 1200 cycles per hour</li><li>(AC-2 / AC-4) 150 cycles per hour</li><li>(AC-3) 1200 cycles per hour</li><li>(DC-13) 900 cycles per hour</li><li>Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li><li>(110 V) 2 Poles in Series, 60 °C 90 A</li><li>(110 V) 2 Poles in Series, 70 °C 80 A</li><li>(110 V) 3 Poles in Series, 40 °C 105 A</li><li>(110 V) 3 Poles in Series, 60 °C 90 A</li><li>(110 V) 3 Poles in Series, 70 °C 80 A</li><li>(220 V) 3 Poles in Series, 40 °C 105 A</li><li>(220 V) 3 Poles in Series, 60 °C 90 A</li><li>(220 V) 3 Poles in Series, 70 °C 80 A</li><li>(72 V) 1-Pole, 40 °C 105 A</li><li>(72 V) 1-Pole, 60 °C 90 A</li><li>(72 V) 1-Pole, 70 °C 80 A</li><li>(72 V) 2 Poles in Series, 40 °C 105 A</li><li>(72 V) 2 Poles in Series, 60 °C 90 A</li><li>(72 V) 2 Poles in Series, 70 °C 80 A</li><li>(72 V) 3 Poles in Series, 40 °C 105 A</li><li>(72 V) 3 Poles in Series, 60 °C 90 A</li><li>(72 V) 3 Poles in Series, 70 °C 80 A</li><li>Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li><li>(110 V) 2 Poles in Series, 60 °C 90 A</li><li>(110 V) 2 Poles in Series, 70 °C 80 A</li><li>(110 V) 3 Poles in Series, 40 °C 105 A</li><li>(110 V) 3 Poles in Series, 60 °C 90 A</li><li>(110 V) 3 Poles in Series, 70 °C 80 A</li><li>(220 V) 3 Poles in Series, 40 °C 105 A</li><li>(220 V) 3 Poles in Series, 60 °C 90 A</li><li>(220 V) 3 Poles in Series, 70 °C 80 A</li><li>(72 V) 1-Pole, 40 °C 105 A</li><li>(72 V) 1-Pole, 60 °C 90 A</li><li>(72 V) 1-Pole, 70 °C 80 A</li><li>(72 V) 2 Poles in Series, 40 °C 105 A</li><li>(72 V) 2 Poles in Series, 60 °C 90 A</li><li>(72 V) 2 Poles in Series, 70 °C 80 A</li><li>(72 V) 3 Poles in Series, 40 °C 105 A</li><li>(72 V) 3 Poles in Series, 60 °C 90 A</li><li>(72 V) 3 Poles in Series, 70 °C 80 A</li><li>Rated Operational Current DC-5 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li><li>(110 V) 2 Poles in Series, 60 °C 90 A</li><li>(110 V) 2 Poles in Series, 70 °C 80 A</li><li>(110 V) 3 Poles in Series, 40 °C 105 A</li><li>(110 V) 3 Poles in Series, 60 °C 90 A</li><li>(110 V) 3 Poles in Series, 70 °C 80 A</li><li>(220 V) 3 Poles in Series, 40 °C 105 A</li><li>(220 V) 3 Poles in Series, 60 °C 90 A</li><li>(220 V) 3 Poles in Series, 70 °C 80 A</li><li>(72 V) 1-Pole, 40 °C 105 A</li><li>(72 V) 1-Pole, 60 °C 90 A</li><li>(72 V) 1-Pole, 70 °C 80 A</li><li>(72 V) 2 Poles in Series, 40 °C 105 A</li><li>(72 V) 2 Poles in Series, 60 °C 90 A</li><li>(72 V) 2 Poles in Series, 70 °C 80 A</li><li>(72 V) 3 Poles in Series, 40 °C 105 A</li><li>(72 V) 3 Poles in Series, 60 °C 90 A</li><li>(72 V) 3 Poles in Series, 70 °C 80 A</li><li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li><li>(48 V) 2.8 A / 134 W</li><li>(72 V) 1 A / 72 W</li><li>(110 V) 0.55 A / 60 W</li><li>(125 V) 0.55 A / 69 W</li><li>(220 V) 0.27 A / 60 W</li><li>(250 V) 0.27 A / 68 W</li><li>(400 V) 0.15 A / 60 W</li><li>(500 V) 0.13 A / 65 W</li><li>(600 V) 0.1 A / 60 W</li><li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li><li>acc. to IEC 60947-5-1 690 V</li><li>acc. to UL/CSA 600 V</li><li>Rated Impulse Withstand Voltage (Uimp):6 kV</li><li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li><li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li><li>60 Hz 100 ... 250 V</li><li>DC Operation 100 ... 250 V</li><li>Coil Consumption:Average Holding Value 50 / 60 Hz 4 V·A</li><li>Average Holding Value 50 Hz 4 V·A</li><li>Average Holding Value 60 Hz 4 V·A</li><li>Average Holding Value DC 2 W</li><li>Average Holding Value, from Warm State 2 W</li><li>Operate Time:Between Coil De-energization and NC Contact Closing 19 ... 105 ms</li><li>Between Coil De-energization and NO Contact Opening 17 ... 100 ms</li><li>Between Coil Energization and NC Contact Opening 38 ... 95 ms</li><li>Between Coil Energization and NO Contact Closing 42 ... 100 ms</li><li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li><li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li><li>Mounting by Screws (not supplied):2 x M4 or 2 x M6 screws placed diagonally</li><li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 4 ... 35 mm²</li><li>Flexible with Insulated Ferrule 1/2x 4 ... 35 mm²</li><li>Rigid Stranded 1/2x 6 ... 35 mm²</li><li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Rigid 1/2x 1 ... 2.5 mm²</li><li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Wire Stripping Length:Auxiliary Circuit 10 mm</li><li>Control Circuit 10 mm</li><li>Main Circuit 16 mm</li><li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP10</li><li>Terminal Type:Screw Terminals</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb AF65-30-11-13 Contactor 3P 30KW 1NO 1NC 50/60HZ 100-250VAC/DC</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:AF65-30-11-13</li>
<li>Product ID:1SBL387001R1311</li>
<li>EAN:3471523132733</li>
<li>Catalog Description:AF65-30-11-13 100-250V50/60HZ-DC Contactor</li>
<li>Long Description:The AF65-30-11-13 is a 3 pole - 690 V IEC or 600 UL contactor with pre-mounted auxiliary contacts and screw terminals, controlling motors up to 30 kW / 400 V AC (AC-3) or 50 hp / 480 V UL and switching power circuits up to 105 A (AC-1) or 90 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li>
<li>Number of Main Contacts NO:3</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:1</li>
<li>Number of Auxiliary Contacts NC:1</li>
<li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-1, UL 60947-4-1, CSA C22.2 No. 60947-1:22, CSA C22.2 No. 60947-4-1:22</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V</li>
<li>Main Circuit 690 V</li>
<li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li>
<li>Control Circuit 50 / 60 Hz</li>
<li>Main Circuit 50 / 60 Hz</li>
<li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 105 A</li>
<li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li>
<li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 105 A</li>
<li>(690 V) 60 °C 90 A</li>
<li>(690 V) 70 °C 80 A</li>
<li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 65 A</li>
<li>(440 V) 60 °C 65 A</li>
<li>(500 V) 60 °C 55 A</li>
<li>(690 V) 60 °C 39 A</li>
<li>(380 / 400 V) 60 °C 65 A</li>
<li>(220 / 230 / 240 V) 60 °C 65 A</li>
<li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 65 A</li>
<li>(440 V) 60 °C 65 A</li>
<li>(500 V) 60 °C 55 A</li>
<li>(690 V) 60 °C 39 A</li>
<li>(380 / 400 V) 60 °C 65 A</li>
<li>(220 / 230 / 240 V) 60 °C 65 A</li>
<li>Rated Operational Power AC-3 (Pe):(400 V) 30 kW</li>
<li>(415 V) 37 kW</li>
<li>(440 V) 37 kW</li>
<li>(500 V) 37 kW</li>
<li>(690 V) 37 kW</li>
<li>(380 / 400 V) 30 kW</li>
<li>(220 / 230 / 240 V) 18.5 kW</li>
<li>Rated Operational Power AC-3e (Pe):(415 V) 37 kW</li>
<li>(440 V) 37 kW</li>
<li>(500 V) 37 kW</li>
<li>(690 V) 37 kW</li>
<li>(380 / 400 V) 30 kW</li>
<li>(220 / 230 / 240 V) 18.5 kW</li>
<li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li>
<li>(690 V) 2 A</li>
<li>(24 / 127 V) 6 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(400 / 440 V) 3 A</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 600 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 110 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 250 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 1000 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 350 A</li>
<li>for 0.1 s 140 A</li>
<li>for 1 s 100 A</li>
<li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 950 A</li>
<li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 600 A</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li>
<li>(AC-15) 1200 cycles per hour</li>
<li>(AC-2 / AC-4) 150 cycles per hour</li>
<li>(AC-3) 1200 cycles per hour</li>
<li>(DC-13) 900 cycles per hour</li>
<li>Rated Operational Current DC-1 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 1-Pole, 40 °C 105 A</li>
<li>(72 V) 1-Pole, 60 °C 90 A</li>
<li>(72 V) 1-Pole, 70 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 80 A</li>
<li>Rated Operational Current DC-3 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 1-Pole, 40 °C 105 A</li>
<li>(72 V) 1-Pole, 60 °C 90 A</li>
<li>(72 V) 1-Pole, 70 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 80 A</li>
<li>Rated Operational Current DC-5 (Ie):(110 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 1-Pole, 40 °C 105 A</li>
<li>(72 V) 1-Pole, 60 °C 90 A</li>
<li>(72 V) 1-Pole, 70 °C 80 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 80 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 105 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 90 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 80 A</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li>
<li>(48 V) 2.8 A / 134 W</li>
<li>(72 V) 1 A / 72 W</li>
<li>(110 V) 0.55 A / 60 W</li>
<li>(125 V) 0.55 A / 69 W</li>
<li>(220 V) 0.27 A / 60 W</li>
<li>(250 V) 0.27 A / 68 W</li>
<li>(400 V) 0.15 A / 60 W</li>
<li>(500 V) 0.13 A / 65 W</li>
<li>(600 V) 0.1 A / 60 W</li>
<li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li>
<li>acc. to IEC 60947-5-1 690 V</li>
<li>acc. to UL/CSA 600 V</li>
<li>Rated Impulse Withstand Voltage (Uimp):6 kV</li>
<li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li>
<li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li>
<li>60 Hz 100 ... 250 V</li>
<li>DC Operation 100 ... 250 V</li>
<li>Coil Consumption:Average Holding Value 50 / 60 Hz 4 V·A</li>
<li>Average Holding Value 50 Hz 4 V·A</li>
<li>Average Holding Value 60 Hz 4 V·A</li>
<li>Average Holding Value DC 2 W</li>
<li>Average Holding Value, from Warm State 2 W</li>
<li>Operate Time:Between Coil De-energization and NC Contact Closing 19 ... 105 ms</li>
<li>Between Coil De-energization and NO Contact Opening 17 ... 100 ms</li>
<li>Between Coil Energization and NC Contact Opening 38 ... 95 ms</li>
<li>Between Coil Energization and NO Contact Closing 42 ... 100 ms</li>
<li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li>
<li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li>
<li>Mounting by Screws (not supplied):2 x M4 or 2 x M6 screws placed diagonally</li>
<li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 4 ... 35 mm²</li>
<li>Flexible with Insulated Ferrule 1/2x 4 ... 35 mm²</li>
<li>Rigid Stranded 1/2x 6 ... 35 mm²</li>
<li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Rigid 1/2x 1 ... 2.5 mm²</li>
<li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Wire Stripping Length:Auxiliary Circuit 10 mm</li>
<li>Control Circuit 10 mm</li>
<li>Main Circuit 16 mm</li>
<li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP10</li>
<li>Terminal Type:Screw Terminals</li>
<li>Unit of Measurement : Pcs</li>
</ul>

abb af65-30-11-13 contactor 3p 30kw 1no 1nc 50/60hz 100-250vac/dc kontaktor contactors para kontraktor penyentuh penghubung 接触器

abb-af65-30-11-13-contactor-3p-30kw-1no-1nc-50-60hz-100-250vac-dc

Abb AF16-30-10-13 Contactor 3P 7.5KW 1NO 50/60HZ 100-250VAC/DC

Catalog Description:AF16-30-10-13 100-250V50/60HZ-DC Contactor

Long Description:The AF16-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 7.5 kW / 400 V AC (AC-3) or 10 hp / 480 V UL and switching power circuits up to 30 A (AC-1) or 30 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.

Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-4-1, CSA C22.2 No. 60947-4-1

Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 35 A

Rated Operational Current AC-1 (Ie):(690 V) 40 °C 30 A

Rated Operational Current AC-3 (Ie):(415 V) 60 °C 18 A

Rated Operational Current AC-3e (Ie):(415 V) 60 °C 18 A

Rated Operational Power AC-3 (Pe):(400 V) 7.5 kW

Rated Operational Power AC-3e (Pe):(415 V) 9 kW

Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 150 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 35 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 60 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 300 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 80 A

Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 440 V 250 A

cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 690 V 106 A

Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 20 A

Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 8 A

<h3 class="md-block-header-three">Abb AF16-30-10-13 Contactor 3P 7.5KW 1NO 50/60HZ 100-250VAC/DC</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:AF16-30-10-13</li><li>Product ID:1SBL177001R1310</li><li>EAN:3471523110632</li><li>Catalog Description:AF16-30-10-13 100-250V50/60HZ-DC Contactor</li><li>Long Description:The AF16-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 7.5 kW / 400 V AC (AC-3) or 10 hp / 480 V UL and switching power circuits up to 30 A (AC-1) or 30 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li><li>Number of Main Contacts NO:3</li><li>Number of Main Contacts NC:0</li><li>Number of Auxiliary Contacts NO:1</li><li>Number of Auxiliary Contacts NC:0</li><li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-4-1, CSA C22.2 No. 60947-4-1</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V</li><li>Main Circuit 690 V</li><li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li><li>Control Circuit 50 / 60 Hz</li><li>Main Circuit 50 / 60 Hz</li><li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 35 A</li><li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li><li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 30 A</li><li>(690 V) 60 °C 30 A</li><li>(690 V) 70 °C 26 A</li><li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 18 A</li><li>(440 V) 60 °C 18 A</li><li>(500 V) 60 °C 15 A</li><li>(690 V) 60 °C 10.5 A</li><li>(380 / 400 V) 60 °C 18 A</li><li>(220 / 230 / 240 V) 60 °C 18 A</li><li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 18 A</li><li>(440 V) 60 °C 18 A</li><li>(500 V) 60 °C 15 A</li><li>(690 V) 60 °C 10.5 A</li><li>(380 / 400 V) 60 °C 18 A</li><li>(220 / 230 / 240 V) 60 °C 18 A</li><li>Rated Operational Power AC-3 (Pe):(400 V) 7.5 kW</li><li>(415 V) 9 kW</li><li>(440 V) 9 kW</li><li>(500 V) 9 kW</li><li>(690 V) 9 kW</li><li>(380 / 400 V) 7.5 kW</li><li>(220 / 230 / 240 V) 4 kW</li><li>Rated Operational Power AC-3e (Pe):(415 V) 9 kW</li><li>(440 V) 9 kW</li><li>(500 V) 9 kW</li><li>(690 V) 9 kW</li><li>(380 / 400 V) 7.5 kW</li><li>(220 / 230 / 240 V) 4 kW</li><li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li><li>(690 V) 2 A</li><li>(24 / 127 V) 6 A</li><li>(220 / 240 V) 4 A</li><li>(400 / 440 V) 3 A</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 150 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 35 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 60 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 300 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 80 A</li><li>for 0.1 s 140 A</li><li>for 1 s 100 A</li><li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 250 A</li><li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 106 A</li><li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li><li>(AC-15) 1200 cycles per hour</li><li>(AC-2 / AC-4) 300 cycles per hour</li><li>(AC-3) 1200 cycles per hour</li><li>(DC-13) 900 cycles per hour</li><li>Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 20 A</li><li>(110 V) 1-Pole, 60 °C 20 A</li><li>(110 V) 1-Pole, 70 °C 20 A</li><li>(110 V) 2 Poles in Series, 40 °C 30 A</li><li>(110 V) 2 Poles in Series, 60 °C 30 A</li><li>(110 V) 2 Poles in Series, 70 °C 26 A</li><li>(110 V) 3 Poles in Series, 40 °C 30 A</li><li>(110 V) 3 Poles in Series, 60 °C 30 A</li><li>(110 V) 3 Poles in Series, 70 °C 26 A</li><li>(220 V) 2 Poles in Series, 40 °C 20 A</li><li>(220 V) 2 Poles in Series, 60 °C 20 A</li><li>(220 V) 2 Poles in Series, 70 °C 20 A</li><li>(220 V) 3 Poles in Series, 40 °C 30 A</li><li>(220 V) 3 Poles in Series, 60 °C 30 A</li><li>(220 V) 3 Poles in Series, 70 °C 26 A</li><li>(72 V) 1-Pole, 40 °C 30 A</li><li>(72 V) 1-Pole, 60 °C 30 A</li><li>(72 V) 1-Pole, 70 °C 26 A</li><li>(72 V) 2 Poles in Series, 40 °C 30 A</li><li>(72 V) 2 Poles in Series, 60 °C 30 A</li><li>(72 V) 2 Poles in Series, 70 °C 26 A</li><li>(72 V) 3 Poles in Series, 40 °C 30 A</li><li>(72 V) 3 Poles in Series, 60 °C 30 A</li><li>(72 V) 3 Poles in Series, 70 °C 26 A</li><li>Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 8 A</li><li>(110 V) 1-Pole, 60 °C 8 A</li><li>(110 V) 1-Pole, 70 °C 8 A</li><li>(110 V) 2 Poles in Series, 40 °C 30 A</li><li>(110 V) 2 Poles in Series, 60 °C 30 A</li><li>(110 V) 2 Poles in Series, 70 °C 26 A</li><li>(110 V) 3 Poles in Series, 40 °C 30 A</li><li>(110 V) 3 Poles in Series, 60 °C 30 A</li><li>(110 V) 3 Poles in Series, 70 °C 26 A</li><li>(220 V) 2 Poles in Series, 40 °C 8 A</li><li>(220 V) 2 Poles in Series, 60 °C 8 A</li><li>(220 V) 2 Poles in Series, 70 °C 8 A</li><li>(220 V) 3 Poles in Series, 40 °C 30 A</li><li>(220 V) 3 Poles in Series, 60 °C 30 A</li><li>(220 V) 3 Poles in Series, 70 °C 26 A</li><li>(72 V) 1-Pole, 40 °C 30 A</li><li>(72 V) 1-Pole, 60 °C 30 A</li><li>(72 V) 1-Pole, 70 °C 26 A</li><li>(72 V) 2 Poles in Series, 40 °C 30 A</li><li>(72 V) 2 Poles in Series, 60 °C 30 A</li><li>(72 V) 2 Poles in Series, 70 °C 26 A</li><li>(72 V) 3 Poles in Series, 40 °C 30 A</li><li>(72 V) 3 Poles in Series, 60 °C 30 A</li><li>(72 V) 3 Poles in Series, 70 °C 26 A</li><li>Rated Operational Current DC-5 (Ie):(110 V) 1-Pole, 40 °C 4 A</li><li>(110 V) 1-Pole, 60 °C 4 A</li><li>(110 V) 1-Pole, 70 °C 4 A</li><li>(110 V) 2 Poles in Series, 40 °C 20 A</li><li>(110 V) 2 Poles in Series, 60 °C 20 A</li><li>(110 V) 2 Poles in Series, 70 °C 20 A</li><li>(110 V) 3 Poles in Series, 40 °C 30 A</li><li>(110 V) 3 Poles in Series, 60 °C 30 A</li><li>(110 V) 3 Poles in Series, 70 °C 26 A</li><li>(220 V) 2 Poles in Series, 40 °C 4 A</li><li>(220 V) 2 Poles in Series, 60 °C 4 A</li><li>(220 V) 2 Poles in Series, 70 °C 4 A</li><li>(220 V) 3 Poles in Series, 40 °C 16 A</li><li>(220 V) 3 Poles in Series, 60 °C 16 A</li><li>(220 V) 3 Poles in Series, 70 °C 16 A</li><li>(72 V) 1-Pole, 40 °C 16 A</li><li>(72 V) 1-Pole, 60 °C 16 A</li><li>(72 V) 1-Pole, 70 °C 16 A</li><li>(72 V) 2 Poles in Series, 40 °C 30 A</li><li>(72 V) 2 Poles in Series, 60 °C 30 A</li><li>(72 V) 2 Poles in Series, 70 °C 26 A</li><li>(72 V) 3 Poles in Series, 40 °C 30 A</li><li>(72 V) 3 Poles in Series, 60 °C 30 A</li><li>(72 V) 3 Poles in Series, 70 °C 26 A</li><li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li><li>(48 V) 2.8 A / 134 W</li><li>(72 V) 1 A / 72 W</li><li>(110 V) 0.55 A / 60 W</li><li>(125 V) 0.55 A / 69 W</li><li>(220 V) 0.27 A / 60 W</li><li>(250 V) 0.27 A / 68 W</li><li>(400 V) 0.15 A / 60 W</li><li>(500 V) 0.13 A / 65 W</li><li>(600 V) 0.1 A / 60 W</li><li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li><li>acc. to IEC 60947-5-1 690 V</li><li>acc. to UL/CSA 600 V</li><li>Rated Impulse Withstand Voltage (Uimp):6 kV</li><li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li><li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li><li>60 Hz 100 ... 250 V</li><li>DC Operation 100 ... 250 V</li><li>Operate Time:Between Coil De-energization and NC Contact Closing 13 ... 98 ms</li><li>Between Coil De-energization and NO Contact Opening 11 ... 95 ms</li><li>Between Coil Energization and NC Contact Opening 38 ... 90 ms</li><li>Between Coil Energization and NO Contact Closing 40 ... 95 ms</li><li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li><li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li><li>Mounting by Screws (not supplied):2 x M4 screws placed diagonally</li><li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 0.75 ... 6 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 4 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 2.5 mm²</li><li>Rigid Solid 1/2x 1 ... 4 mm²</li><li>Rigid Stranded 1/2x 1 ... 6 mm²</li><li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Wire Stripping Length:Auxiliary Circuit 10 mm</li><li>Control Circuit 10 mm</li><li>Main Circuit 10 mm</li><li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li><li>Terminal Type:Screw Terminals</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb AF16-30-10-13 Contactor 3P 7.5KW 1NO 50/60HZ 100-250VAC/DC</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:AF16-30-10-13</li>
<li>Product ID:1SBL177001R1310</li>
<li>EAN:3471523110632</li>
<li>Catalog Description:AF16-30-10-13 100-250V50/60HZ-DC Contactor</li>
<li>Long Description:The AF16-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 7.5 kW / 400 V AC (AC-3) or 10 hp / 480 V UL and switching power circuits up to 30 A (AC-1) or 30 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li>
<li>Number of Main Contacts NO:3</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:1</li>
<li>Number of Auxiliary Contacts NC:0</li>
<li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-4-1, CSA C22.2 No. 60947-4-1</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V</li>
<li>Main Circuit 690 V</li>
<li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li>
<li>Control Circuit 50 / 60 Hz</li>
<li>Main Circuit 50 / 60 Hz</li>
<li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 35 A</li>
<li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li>
<li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 30 A</li>
<li>(690 V) 60 °C 30 A</li>
<li>(690 V) 70 °C 26 A</li>
<li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 18 A</li>
<li>(440 V) 60 °C 18 A</li>
<li>(500 V) 60 °C 15 A</li>
<li>(690 V) 60 °C 10.5 A</li>
<li>(380 / 400 V) 60 °C 18 A</li>
<li>(220 / 230 / 240 V) 60 °C 18 A</li>
<li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 18 A</li>
<li>(440 V) 60 °C 18 A</li>
<li>(500 V) 60 °C 15 A</li>
<li>(690 V) 60 °C 10.5 A</li>
<li>(380 / 400 V) 60 °C 18 A</li>
<li>(220 / 230 / 240 V) 60 °C 18 A</li>
<li>Rated Operational Power AC-3 (Pe):(400 V) 7.5 kW</li>
<li>(415 V) 9 kW</li>
<li>(440 V) 9 kW</li>
<li>(500 V) 9 kW</li>
<li>(690 V) 9 kW</li>
<li>(380 / 400 V) 7.5 kW</li>
<li>(220 / 230 / 240 V) 4 kW</li>
<li>Rated Operational Power AC-3e (Pe):(415 V) 9 kW</li>
<li>(440 V) 9 kW</li>
<li>(500 V) 9 kW</li>
<li>(690 V) 9 kW</li>
<li>(380 / 400 V) 7.5 kW</li>
<li>(220 / 230 / 240 V) 4 kW</li>
<li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li>
<li>(690 V) 2 A</li>
<li>(24 / 127 V) 6 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(400 / 440 V) 3 A</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 150 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 35 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 60 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 300 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 80 A</li>
<li>for 0.1 s 140 A</li>
<li>for 1 s 100 A</li>
<li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 250 A</li>
<li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 106 A</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li>
<li>(AC-15) 1200 cycles per hour</li>
<li>(AC-2 / AC-4) 300 cycles per hour</li>
<li>(AC-3) 1200 cycles per hour</li>
<li>(DC-13) 900 cycles per hour</li>
<li>Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 20 A</li>
<li>(110 V) 1-Pole, 60 °C 20 A</li>
<li>(110 V) 1-Pole, 70 °C 20 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 30 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 30 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 26 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 26 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 20 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 20 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 20 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 26 A</li>
<li>(72 V) 1-Pole, 40 °C 30 A</li>
<li>(72 V) 1-Pole, 60 °C 30 A</li>
<li>(72 V) 1-Pole, 70 °C 26 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 26 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 26 A</li>
<li>Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 8 A</li>
<li>(110 V) 1-Pole, 60 °C 8 A</li>
<li>(110 V) 1-Pole, 70 °C 8 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 30 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 30 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 26 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 26 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 8 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 8 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 8 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 26 A</li>
<li>(72 V) 1-Pole, 40 °C 30 A</li>
<li>(72 V) 1-Pole, 60 °C 30 A</li>
<li>(72 V) 1-Pole, 70 °C 26 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 26 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 26 A</li>
<li>Rated Operational Current DC-5 (Ie):(110 V) 1-Pole, 40 °C 4 A</li>
<li>(110 V) 1-Pole, 60 °C 4 A</li>
<li>(110 V) 1-Pole, 70 °C 4 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 20 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 20 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 20 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 26 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 4 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 4 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 4 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 16 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 16 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 16 A</li>
<li>(72 V) 1-Pole, 40 °C 16 A</li>
<li>(72 V) 1-Pole, 60 °C 16 A</li>
<li>(72 V) 1-Pole, 70 °C 16 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 26 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 30 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 26 A</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li>
<li>(48 V) 2.8 A / 134 W</li>
<li>(72 V) 1 A / 72 W</li>
<li>(110 V) 0.55 A / 60 W</li>
<li>(125 V) 0.55 A / 69 W</li>
<li>(220 V) 0.27 A / 60 W</li>
<li>(250 V) 0.27 A / 68 W</li>
<li>(400 V) 0.15 A / 60 W</li>
<li>(500 V) 0.13 A / 65 W</li>
<li>(600 V) 0.1 A / 60 W</li>
<li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li>
<li>acc. to IEC 60947-5-1 690 V</li>
<li>acc. to UL/CSA 600 V</li>
<li>Rated Impulse Withstand Voltage (Uimp):6 kV</li>
<li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li>
<li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li>
<li>60 Hz 100 ... 250 V</li>
<li>DC Operation 100 ... 250 V</li>
<li>Operate Time:Between Coil De-energization and NC Contact Closing 13 ... 98 ms</li>
<li>Between Coil De-energization and NO Contact Opening 11 ... 95 ms</li>
<li>Between Coil Energization and NC Contact Opening 38 ... 90 ms</li>
<li>Between Coil Energization and NO Contact Closing 40 ... 95 ms</li>
<li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li>
<li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li>
<li>Mounting by Screws (not supplied):2 x M4 screws placed diagonally</li>
<li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 0.75 ... 6 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 4 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 2.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 4 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 6 mm²</li>
<li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Wire Stripping Length:Auxiliary Circuit 10 mm</li>
<li>Control Circuit 10 mm</li>
<li>Main Circuit 10 mm</li>
<li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li>
<li>Terminal Type:Screw Terminals</li>
<li>Unit of Measurement : Pcs</li>
</ul>

abb af16-30-10-13 contactor 3p 7.5kw 1no 50/60hz 100-250vac/dc kontaktor contactors para kontraktor penyentuh penghubung 接触器

abb-af16-30-10-13-contactor-3p-7-5kw-1no-50-60hz-100-250vac-dc

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).  

Overview on Application Rating for Material Nitrile (NBR)  

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.  

Applications that require resistance to OIL 

Applications that are required to work in low temperatures (-0°C) 

High performance Fuel systems that requires strictly no leakage

Covering 	and lubricating the threading of the shaft 

ORING AS568 AS122 ID 28.24 X CS 2.62Material : Nitrile (NBR) 90 Shore Additional InformationNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance. Primary UsageO-Rings and rubber seals are generally used for:<ul class="md-block-unordered-list-item"><li>Applications that require resistance to OIL </li><li>Applications that are required to work in low temperatures (-0°C) </li><li>High performance Fuel systems that requires strictly no leakage</li><ul class="md-block-unordered-list-item"><li>Aircrafts </li><li>Marine Ships </li><li>F1 Cars</li></ul><li>General Industrial Use </li></ul>Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:<ul class="md-block-unordered-list-item"><li>Covering 	and lubricating the threading of the shaft </li></ul>The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.<ul class="md-block-unordered-list-item"><li>Don’t force it over sharp corners </li></ul>That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.<ul class="md-block-unordered-list-item"><li>Even stretching </li></ul>You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.<ul class="md-block-unordered-list-item"><li>Don’t roll it down the shaft </li></ul>Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.<ul class="md-block-unordered-list-item"><li>Finishing 	it off </li></ul>Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/EljpgvOUve96R8e3bH8~lh.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING AS568 AS122
&nbsp;ID 28.24 X CS 2.62
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;<ins>Additional Information</ins>
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>&nbsp;
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder. Durometer is also generally stated and accepted with a “+/- 5” tolerance.&nbsp;&nbsp;
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
<ul>
<li>Applications that require resistance to OIL&nbsp;</li>
<li>Applications that are required to work in low temperatures (-0°C)&nbsp;</li>
<li>High performance Fuel systems that requires strictly no leakage</li>
<ul>
<li>Aircrafts&nbsp;</li>
<li>Marine Ships&nbsp;</li>
<li>F1 Cars</li>
</ul>
<li>General Industrial Use&nbsp;&nbsp;&nbsp;</li>
</ul>
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
<ul>
<li>Covering 	and lubricating the threading of the shaft&nbsp;</li>
</ul>
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
<ul>
<li>Don’t force it over sharp corners&nbsp;</li>
</ul>
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
<ul>
<li>Even stretching&nbsp;</li>
</ul>
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
<ul>
<li>Don’t roll it down the shaft&nbsp;</li>
</ul>
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
<ul>
<li>Finishing 	it off&nbsp;</li>
</ul>
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:fpb73"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/EljpgvOUve96R8e3bH8~lh.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="fpb73" 
 layout="nodisplay"></amp-image-lightbox>

ORING AS568 AS122 ID 28.24 X CS 2.62 Nitrile (NBR) 90 Shore

oring as568 as122 id 28.24 cs 2.62 nitrile (nbr) 90 shore ring o-ring oem gelang oem/oem代工 2.62腈（nbr）90肖氏 o型圈 oem代工

oring-as568-as122-id-28-24-x-cs-2-62-nitrile-nbr-90-shore

Abb AX40-30-10-80 Contactor 3P 11KW 3NO 1AUX 50/60HZ 230-240VAC

Catalog Description:AX40-30-10-80 220-230V50Hz/230-240V60Hz Contactor

Long Description:AX32, AX40 contactors are mainly used for controlling 3-phase motors and power circuits up to 690 V AC. These contactors are of the block type design with: – 3 main poles and 1 built-in auxiliary contact – control circuit: AC operated – add-on auxiliary contact blocks for front or side mounting and a wide range of accessories.

Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 65 A

Rated Operational Current AC-1 (Ie):(220 / 240 V) 55 °C 60 A

Rated Operational Current AC-3 (Ie):(415 V) 55 °C 40 A

Rated Operational Power AC-3 (Pe):(415 V) 18.5 kW

Rated Operational Current AC-15 (Ie):(500 V) NC 2

Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 400 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 65 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 150 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 600 A

at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 225 A

Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 440 V 820 A

cos phi=0.45 (cos phi=0.35 for Ie > 100 A) at 690 V 340 A

Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W

Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 and VDE 0110 (Gr. C) 690 V

Rated Impulse Withstand Voltage (Uimp):Auxiliary Circuit 6 kV

Maximum Mechanical Switching Frequency:3600 cycles per hour

Rated Control Circuit Voltage (Uc):50 Hz 220 ... 230 V

Operate Time:Between Coil De-energization and NC Contact Closing 7 ... 14 ms

Between Coil De-energization and NO Contact Opening 4 ... 11 ms

Between Coil Energization and NC Contact Opening 6 ... 18 ms

Between Coil Energization and NO Contact Closing 8 ... 21 ms

Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20

acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20

acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20

<h3 class="md-block-header-three">Abb AX40-30-10-80 Contactor 3P 11KW 3NO 1AUX 50/60HZ 230-240VAC</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:AX40-30-10-80</li><li>Product ID:1SBL321074R8010</li><li>EAN:3471522401809</li><li>Catalog Description:AX40-30-10-80 220-230V50Hz/230-240V60Hz Contactor</li><li>Long Description:AX32, AX40 contactors are mainly used for controlling 3-phase motors and power circuits up to 690 V AC. These contactors are of the block type design with: – 3 main poles and 1 built-in auxiliary contact – control circuit: AC operated – add-on auxiliary contact blocks for front or side mounting and a wide range of accessories.</li><li>Number of Main Contacts NO:3</li><li>Number of Main Contacts NC:0</li><li>Number of Auxiliary Contacts NO:1</li><li>Number of Auxiliary Contacts NC:0</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V</li><li>Main Circuit 690 V</li><li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li><li>Main Circuit 50 / 60 Hz</li><li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 65 A</li><li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li><li>Rated Operational Current AC-1 (Ie):(220 / 240 V) 55 °C 60 A</li><li>(690 V) 40 °C 60 A</li><li>(690 V) 70 °C 42 A</li><li>Rated Operational Current AC-3 (Ie):(415 V) 55 °C 40 A</li><li>(440 V) 55 °C 37 A</li><li>(500 V) 55 °C 33 A</li><li>(690 V) 55 °C 25 A</li><li>(380 / 400 V) 55 °C 40 A</li><li>(220 / 230 / 240 V) 55 °C 40 A</li><li>Rated Operational Power AC-3 (Pe):(415 V) 18.5 kW</li><li>(440 V) 22 kW</li><li>(500 V) 22 kW</li><li>(690 V) 22 kW</li><li>(380 / 400 V) 18.5 kW</li><li>(220 / 230 / 240 V) 11 kW</li><li>Rated Operational Current AC-15 (Ie):(500 V) NC 2</li><li>(500 V) 2 A</li><li>(690 V) 2 A</li><li>(24 / 127 V) 6 A</li><li>(220 / 240 V) 4 A</li><li>(380 / 400 V) 3 A</li><li>(400 / 440 V) 2 A</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 400 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 65 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 150 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 600 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 225 A</li><li>for 0.1 s 140 A</li><li>for 1 s 100 A</li><li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 820 A</li><li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 340 A</li><li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li><li>(AC-15) 1200 cycles per hour</li><li>(AC-3) 1200 cycles per hour</li><li>(DC-13) 900 cycles per hour</li><li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li><li>(110 V) 1.1 A / 121 W</li><li>(125 V) 1.1 A / 138 W</li><li>(220 V) 0.55 A / 121 W</li><li>(250 V) 0.55 A / 138 W</li><li>(400 V) 2.8 A / 134 W</li><li>(500 V) 2 A / 144 W</li><li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 and VDE 0110 (Gr. C) 690 V</li><li>Rated Impulse Withstand Voltage (Uimp):Auxiliary Circuit 6 kV</li><li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li><li>Rated Control Circuit Voltage (Uc):50 Hz 220 ... 230 V</li><li>60 Hz 230 ... 240 V</li><li>Operate Time:Between Coil De-energization and NC Contact Closing 7 ... 14 ms</li><li>Between Coil De-energization and NO Contact Opening 4 ... 11 ms</li><li>Between Coil Energization and NC Contact Opening 6 ... 18 ms</li><li>Between Coil Energization and NO Contact Closing 8 ... 21 ms</li><li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li><li>IP20</li><li>Terminal Type:Screw Terminals</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb AX40-30-10-80 Contactor 3P 11KW 3NO 1AUX 50/60HZ 230-240VAC</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:AX40-30-10-80</li>
<li>Product ID:1SBL321074R8010</li>
<li>EAN:3471522401809</li>
<li>Catalog Description:AX40-30-10-80 220-230V50Hz/230-240V60Hz Contactor</li>
<li>Long Description:AX32, AX40 contactors are mainly used for controlling 3-phase motors and power circuits up to 690 V AC. These contactors are of the block type design with: – 3 main poles and 1 built-in auxiliary contact – control circuit: AC operated – add-on auxiliary contact blocks for front or side mounting and a wide range of accessories.</li>
<li>Number of Main Contacts NO:3</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:1</li>
<li>Number of Auxiliary Contacts NC:0</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V</li>
<li>Main Circuit 690 V</li>
<li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li>
<li>Main Circuit 50 / 60 Hz</li>
<li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 65 A</li>
<li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li>
<li>Rated Operational Current AC-1 (Ie):(220 / 240 V) 55 °C 60 A</li>
<li>(690 V) 40 °C 60 A</li>
<li>(690 V) 70 °C 42 A</li>
<li>Rated Operational Current AC-3 (Ie):(415 V) 55 °C 40 A</li>
<li>(440 V) 55 °C 37 A</li>
<li>(500 V) 55 °C 33 A</li>
<li>(690 V) 55 °C 25 A</li>
<li>(380 / 400 V) 55 °C 40 A</li>
<li>(220 / 230 / 240 V) 55 °C 40 A</li>
<li>Rated Operational Power AC-3 (Pe):(415 V) 18.5 kW</li>
<li>(440 V) 22 kW</li>
<li>(500 V) 22 kW</li>
<li>(690 V) 22 kW</li>
<li>(380 / 400 V) 18.5 kW</li>
<li>(220 / 230 / 240 V) 11 kW</li>
<li>Rated Operational Current AC-15 (Ie):(500 V) NC 2</li>
<li>(500 V) 2 A</li>
<li>(690 V) 2 A</li>
<li>(24 / 127 V) 6 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(380 / 400 V) 3 A</li>
<li>(400 / 440 V) 2 A</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 400 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 65 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 150 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 600 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 225 A</li>
<li>for 0.1 s 140 A</li>
<li>for 1 s 100 A</li>
<li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 820 A</li>
<li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 340 A</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li>
<li>(AC-15) 1200 cycles per hour</li>
<li>(AC-3) 1200 cycles per hour</li>
<li>(DC-13) 900 cycles per hour</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li>
<li>(110 V) 1.1 A / 121 W</li>
<li>(125 V) 1.1 A / 138 W</li>
<li>(220 V) 0.55 A / 121 W</li>
<li>(250 V) 0.55 A / 138 W</li>
<li>(400 V) 2.8 A / 134 W</li>
<li>(500 V) 2 A / 144 W</li>
<li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 and VDE 0110 (Gr. C) 690 V</li>
<li>Rated Impulse Withstand Voltage (Uimp):Auxiliary Circuit 6 kV</li>
<li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li>
<li>Rated Control Circuit Voltage (Uc):50 Hz 220 ... 230 V</li>
<li>60 Hz 230 ... 240 V</li>
<li>Operate Time:Between Coil De-energization and NC Contact Closing 7 ... 14 ms</li>
<li>Between Coil De-energization and NO Contact Opening 4 ... 11 ms</li>
<li>Between Coil Energization and NC Contact Opening 6 ... 18 ms</li>
<li>Between Coil Energization and NO Contact Closing 8 ... 21 ms</li>
<li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li>
<li>IP20</li>
<li>Terminal Type:Screw Terminals</li>
<li>Unit of Measurement : Pcs</li>
</ul>

abb ax40-30-10-80 contactor 3p 11kw 3no 1aux 50/60hz 230-240vac kontaktor contactors para kontraktor penyentuh penghubung 接触器

abb-ax40-30-10-80-contactor-3p-11kw-3no-1aux-50-60hz-230-240vac

Abb AF09-30-01-13 Contactor 100-250VAC/DC 3P 4KW 1NC

Catalog Description:AF09-30-10-13 100-250V50/60HZ-DC Contactor

Long Description:The AF09-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 4 kW / 400 V AC (AC-3) or 5 hp / 480 V UL and switching power circuits up to 25 A (AC-1) or 25 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.

Rated Operational Current AC-1 (Ie):(690 V) 40 °C 25 A

Rated Operational Current AC-3 (Ie):(415 V) 60 °C 9 A

Rated Operational Current AC-3e (Ie):(415 V) 60 °C 9 A

Rated Operational Power AC-3 (Pe):(400 V) 4 kW

Rated Operational Power AC-3e (Pe):(415 V) 4 kW

Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 10 A

Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 6 A

<h3 class="md-block-header-three">Abb AF09-30-01-13 Contactor 100-250VAC/DC 3P 4KW 1NC</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:AF09-30-10-13</li><li>Product ID:1SBL137001R1310</li><li>EAN:3471523110038</li><li>Catalog Description:AF09-30-10-13 100-250V50/60HZ-DC Contactor</li><li>Long Description:The AF09-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 4 kW / 400 V AC (AC-3) or 5 hp / 480 V UL and switching power circuits up to 25 A (AC-1) or 25 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li><li>Number of Main Contacts NO:3</li><li>Number of Main Contacts NC:0</li><li>Number of Auxiliary Contacts NO:0</li><li>Number of Auxiliary Contacts NC:1</li><li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-4-1, CSA C22.2 No. 60947-4-1</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V</li><li>Main Circuit 690 V</li><li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li><li>Control Circuit 50 / 60 Hz</li><li>Main Circuit 50 / 60 Hz</li><li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 35 A</li><li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li><li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 25 A</li><li>(690 V) 60 °C 25 A</li><li>(690 V) 70 °C 22 A</li><li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 9 A</li><li>(440 V) 60 °C 9 A</li><li>(500 V) 60 °C 9.5 A</li><li>(690 V) 60 °C 7 A</li><li>(380 / 400 V) 60 °C 9 A</li><li>(220 / 230 / 240 V) 60 °C 9 A</li><li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 9 A</li><li>(440 V) 60 °C 9 A</li><li>(500 V) 60 °C 9.5 A</li><li>(690 V) 60 °C 7 A</li><li>(380 / 400 V) 60 °C 9 A</li><li>(220 / 230 / 240 V) 60 °C 9 A</li><li>Rated Operational Power AC-3 (Pe):(400 V) 4 kW</li><li>(415 V) 4 kW</li><li>(440 V) 4 kW</li><li>(500 V) 5.5 kW</li><li>(690 V) 5.5 kW</li><li>(380 / 400 V) 4 kW</li><li>(220 / 230 / 240 V) 2.2 kW</li><li>Rated Operational Power AC-3e (Pe):(415 V) 4 kW</li><li>(440 V) 4 kW</li><li>(500 V) 5.5 kW</li><li>(690 V) 5.5 kW</li><li>(380 / 400 V) 4 kW</li><li>(220 / 230 / 240 V) 2.2 kW</li><li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li><li>(690 V) 2 A</li><li>(24 / 127 V) 6 A</li><li>(220 / 240 V) 4 A</li><li>(400 / 440 V) 3 A</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 150 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 35 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 60 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 300 A</li><li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 80 A</li><li>for 0.1 s 140 A</li><li>for 1 s 100 A</li><li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 250 A</li><li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 106 A</li><li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li><li>(AC-15) 1200 cycles per hour</li><li>(AC-2 / AC-4) 300 cycles per hour</li><li>(AC-3) 1200 cycles per hour</li><li>(DC-13) 900 cycles per hour</li><li>Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 10 A</li><li>(110 V) 1-Pole, 60 °C 10 A</li><li>(110 V) 1-Pole, 70 °C 10 A</li><li>(110 V) 2 Poles in Series, 40 °C 25 A</li><li>(110 V) 2 Poles in Series, 60 °C 25 A</li><li>(110 V) 2 Poles in Series, 70 °C 22 A</li><li>(110 V) 3 Poles in Series, 40 °C 25 A</li><li>(110 V) 3 Poles in Series, 60 °C 25 A</li><li>(110 V) 3 Poles in Series, 70 °C 22 A</li><li>(220 V) 2 Poles in Series, 40 °C 10 A</li><li>(220 V) 2 Poles in Series, 60 °C 10 A</li><li>(220 V) 2 Poles in Series, 70 °C 10 A</li><li>(220 V) 3 Poles in Series, 40 °C 25 A</li><li>(220 V) 3 Poles in Series, 60 °C 25 A</li><li>(220 V) 3 Poles in Series, 70 °C 22 A</li><li>(72 V) 1-Pole, 40 °C 25 A</li><li>(72 V) 1-Pole, 60 °C 25 A</li><li>(72 V) 1-Pole, 70 °C 22 A</li><li>(72 V) 2 Poles in Series, 40 °C 25 A</li><li>(72 V) 2 Poles in Series, 60 °C 25 A</li><li>(72 V) 2 Poles in Series, 70 °C 22 A</li><li>(72 V) 3 Poles in Series, 40 °C 25 A</li><li>(72 V) 3 Poles in Series, 60 °C 25 A</li><li>(72 V) 3 Poles in Series, 70 °C 22 A</li><li>Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 6 A</li><li>(110 V) 1-Pole, 60 °C 6 A</li><li>(110 V) 1-Pole, 70 °C 6 A</li><li>(110 V) 2 Poles in Series, 40 °C 25 A</li><li>(110 V) 2 Poles in Series, 60 °C 25 A</li><li>(110 V) 2 Poles in Series, 70 °C 22 A</li><li>(110 V) 3 Poles in Series, 40 °C 25 A</li><li>(110 V) 3 Poles in Series, 60 °C 25 A</li><li>(110 V) 3 Poles in Series, 70 °C 22 A</li><li>(220 V) 2 Poles in Series, 40 °C 6 A</li><li>(220 V) 2 Poles in Series, 60 °C 6 A</li><li>(220 V) 2 Poles in Series, 70 °C 6 A</li><li>(220 V) 3 Poles in Series, 40 °C 25 A</li><li>(220 V) 3 Poles in Series, 60 °C 25 A</li><li>(220 V) 3 Poles in Series, 70 °C 22 A</li><li>(72 V) 1-Pole, 40 °C 25 A</li><li>(72 V) 1-Pole, 60 °C 25 A</li><li>(72 V) 1-Pole, 70 °C 22 A</li><li>(72 V) 2 Poles in Series, 40 °C 25 A</li><li>(72 V) 2 Poles in Series, 60 °C 25 A</li><li>(72 V) 2 Poles in Series, 70 °C 22 A</li><li>(72 V) 3 Poles in Series, 40 °C 25 A</li><li>(72 V) 3 Poles in Series, 60 °C 25 A</li><li>(72 V) 3 Poles in Series, 70 °C 22 A</li><li>Rated Operational Current DC-5 (Ie):(110 V) 1-Pole, 40 °C 4 A</li><li>(110 V) 1-Pole, 60 °C 4 A</li><li>(110 V) 1-Pole, 70 °C 4 A</li><li>(110 V) 2 Poles in Series, 40 °C 10 A</li><li>(110 V) 2 Poles in Series, 60 °C 10 A</li><li>(110 V) 2 Poles in Series, 70 °C 10 A</li><li>(110 V) 3 Poles in Series, 40 °C 25 A</li><li>(110 V) 3 Poles in Series, 60 °C 25 A</li><li>(110 V) 3 Poles in Series, 70 °C 22 A</li><li>(220 V) 2 Poles in Series, 40 °C 4 A</li><li>(220 V) 2 Poles in Series, 60 °C 4 A</li><li>(220 V) 2 Poles in Series, 70 °C 4 A</li><li>(220 V) 3 Poles in Series, 40 °C 9 A</li><li>(220 V) 3 Poles in Series, 60 °C 9 A</li><li>(220 V) 3 Poles in Series, 70 °C 9 A</li><li>(72 V) 1-Pole, 40 °C 9 A</li><li>(72 V) 1-Pole, 60 °C 9 A</li><li>(72 V) 1-Pole, 70 °C 9 A</li><li>(72 V) 2 Poles in Series, 40 °C 25 A</li><li>(72 V) 2 Poles in Series, 60 °C 25 A</li><li>(72 V) 2 Poles in Series, 70 °C 22 A</li><li>(72 V) 3 Poles in Series, 40 °C 25 A</li><li>(72 V) 3 Poles in Series, 60 °C 25 A</li><li>(72 V) 3 Poles in Series, 70 °C 22 A</li><li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li><li>(48 V) 2.8 A / 134 W</li><li>(72 V) 1 A / 72 W</li><li>(110 V) 0.55 A / 60 W</li><li>(125 V) 0.55 A / 69 W</li><li>(220 V) 0.27 A / 60 W</li><li>(250 V) 0.27 A / 68 W</li><li>(400 V) 0.15 A / 60 W</li><li>(500 V) 0.13 A / 65 W</li><li>(600 V) 0.1 A / 60 W</li><li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li><li>acc. to IEC 60947-5-1 690 V</li><li>acc. to UL/CSA 600 V</li><li>Rated Impulse Withstand Voltage (Uimp):6 kV</li><li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li><li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li><li>60 Hz 100 ... 250 V</li><li>DC Operation 100 ... 250 V</li><li>Operate Time:Between Coil De-energization and NC Contact Closing 13 ... 98 ms</li><li>Between Coil De-energization and NO Contact Opening 11 ... 95 ms</li><li>Between Coil Energization and NC Contact Opening 38 ... 90 ms</li><li>Between Coil Energization and NO Contact Closing 40 ... 95 ms</li><li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li><li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li><li>Mounting by Screws (not supplied):2 x M4 screws placed diagonally</li><li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 0.75 ... 6 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 4 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 2.5 mm²</li><li>Rigid Solid 1/2x 1 ... 4 mm²</li><li>Rigid Stranded 1/2x 1 ... 6 mm²</li><li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li><li>Rigid Solid 1/2x 1 ... 2.5 mm²</li><li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li><li>Wire Stripping Length:Auxiliary Circuit 10 mm</li><li>Control Circuit 10 mm</li><li>Main Circuit 10 mm</li><li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li><li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li><li>Terminal Type:Screw Terminals</li></ul>Technical UL/CSA<ul class="md-block-unordered-list-item"><li>NEMA Size:00</li><li>Continuous Current Rating NEMA:9 A</li><li>Horsepower Rating NEMA:(115 V AC) Single Phase 1/3 Hp</li><li>(200 V AC) Three Phase 1-1/2 Hp</li><li>(230 V AC) Single Phase 1 Hp</li><li>(230 V AC) Three Phase 1-1/2 Hp</li><li>(460 V AC) Three Phase 2 Hp</li><li>(575 V AC) Three Phase 2 Hp</li><li>Maximum Operating Voltage UL/CSA:Main Circuit 600 V</li><li>General Use Rating UL/CSA:(600 V AC) 25 A</li><li>Horsepower Rating UL/CSA:(120 V AC) Single Phase 3/4 hp</li><li>(200 ... 208 V AC) Three Phase 2 hp</li><li>(220 ... 240 V AC) Three Phase 2 hp</li><li>(240 V AC) Single Phase 1-1/2 hp</li><li>(440 ... 480 V AC) Three Phase 5 hp</li><li>(550 ... 600 V AC) Three Phase 7-1/2 hp</li><li>Connecting Capacity Main Circuit UL/CSA:Rigid Solid 1/2x 16-10 AWG</li><li>Rigid Stranded 1/2x 16-10 AWG</li><li>Connecting Capacity Auxiliary Circuit UL/CSA:Rigid Solid 1/2x 18-14 AWG</li><li>Rigid Stranded 1/2x 18-14 AWG</li><li>Connecting Capacity Control Circuit UL/CSA:Rigid Solid 1/2x 18-14 AWG</li><li>Rigid Stranded 1/2x 18-14 AWG</li><li>Tightening Torque UL/CSA:Auxiliary Circuit 11 in·lb</li><li>Control Circuit 11 in·lb</li><li>Main Circuit 13 in·lb</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb AF09-30-01-13 Contactor 100-250VAC/DC 3P 4KW 1NC</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:AF09-30-10-13</li>
<li>Product ID:1SBL137001R1310</li>
<li>EAN:3471523110038</li>
<li>Catalog Description:AF09-30-10-13 100-250V50/60HZ-DC Contactor</li>
<li>Long Description:The AF09-30-10-13 is a 3 pole - 690 V IEC or 600 UL contactor with 1 built-in auxiliary contact and screw terminals, controlling motors up to 4 kW / 400 V AC (AC-3) or 5 hp / 480 V UL and switching power circuits up to 25 A (AC-1) or 25 A UL general use. Thanks to the AF technology, the contactor has a wide control voltage range (100-250 V 50/60 Hz and DC), managing large control voltage variations, reducing panel energy consumptions and ensuring distinct operations in unstable networks. Furthermore, surge protection is built-in, offering a compact solution. AF contactors have a block type design, can be easily extended with add-on auxiliary contact blocks and an additional wide range of accessories.</li>
<li>Number of Main Contacts NO:3</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:0</li>
<li>Number of Auxiliary Contacts NC:1</li>
<li>Standards:IEC/EN 60947-1, IEC/EN 60947-4-1, UL 60947-4-1, CSA C22.2 No. 60947-4-1</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V</li>
<li>Main Circuit 690 V</li>
<li>Rated Frequency (f):Auxiliary Circuit 50 / 60 Hz</li>
<li>Control Circuit 50 / 60 Hz</li>
<li>Main Circuit 50 / 60 Hz</li>
<li>Conventional Free-air Thermal Current (Ith):acc. to IEC 60947-4-1, Open Contactors Θ = 40 °C 35 A</li>
<li>acc. to IEC 60947-5-1, Θ = 40 °C 16 A</li>
<li>Rated Operational Current AC-1 (Ie):(690 V) 40 °C 25 A</li>
<li>(690 V) 60 °C 25 A</li>
<li>(690 V) 70 °C 22 A</li>
<li>Rated Operational Current AC-3 (Ie):(415 V) 60 °C 9 A</li>
<li>(440 V) 60 °C 9 A</li>
<li>(500 V) 60 °C 9.5 A</li>
<li>(690 V) 60 °C 7 A</li>
<li>(380 / 400 V) 60 °C 9 A</li>
<li>(220 / 230 / 240 V) 60 °C 9 A</li>
<li>Rated Operational Current AC-3e (Ie):(415 V) 60 °C 9 A</li>
<li>(440 V) 60 °C 9 A</li>
<li>(500 V) 60 °C 9.5 A</li>
<li>(690 V) 60 °C 7 A</li>
<li>(380 / 400 V) 60 °C 9 A</li>
<li>(220 / 230 / 240 V) 60 °C 9 A</li>
<li>Rated Operational Power AC-3 (Pe):(400 V) 4 kW</li>
<li>(415 V) 4 kW</li>
<li>(440 V) 4 kW</li>
<li>(500 V) 5.5 kW</li>
<li>(690 V) 5.5 kW</li>
<li>(380 / 400 V) 4 kW</li>
<li>(220 / 230 / 240 V) 2.2 kW</li>
<li>Rated Operational Power AC-3e (Pe):(415 V) 4 kW</li>
<li>(440 V) 4 kW</li>
<li>(500 V) 5.5 kW</li>
<li>(690 V) 5.5 kW</li>
<li>(380 / 400 V) 4 kW</li>
<li>(220 / 230 / 240 V) 2.2 kW</li>
<li>Rated Operational Current AC-15 (Ie):(500 V) 2 A</li>
<li>(690 V) 2 A</li>
<li>(24 / 127 V) 6 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(400 / 440 V) 3 A</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 150 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 15 min 35 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 min 60 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 1 s 300 A</li>
<li>at 40 °C Ambient Temp, in Free Air, from a Cold State 30 s 80 A</li>
<li>for 0.1 s 140 A</li>
<li>for 1 s 100 A</li>
<li>Maximum Breaking Capacity:cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 440 V 250 A</li>
<li>cos phi=0.45 (cos phi=0.35 for Ie &gt; 100 A) at 690 V 106 A</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 600 cycles per hour</li>
<li>(AC-15) 1200 cycles per hour</li>
<li>(AC-2 / AC-4) 300 cycles per hour</li>
<li>(AC-3) 1200 cycles per hour</li>
<li>(DC-13) 900 cycles per hour</li>
<li>Rated Operational Current DC-1 (Ie):(110 V) 1-Pole, 40 °C 10 A</li>
<li>(110 V) 1-Pole, 60 °C 10 A</li>
<li>(110 V) 1-Pole, 70 °C 10 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 25 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 25 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 22 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 22 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 10 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 10 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 10 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 22 A</li>
<li>(72 V) 1-Pole, 40 °C 25 A</li>
<li>(72 V) 1-Pole, 60 °C 25 A</li>
<li>(72 V) 1-Pole, 70 °C 22 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 22 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 22 A</li>
<li>Rated Operational Current DC-3 (Ie):(110 V) 1-Pole, 40 °C 6 A</li>
<li>(110 V) 1-Pole, 60 °C 6 A</li>
<li>(110 V) 1-Pole, 70 °C 6 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 25 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 25 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 22 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 22 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 6 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 6 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 6 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 22 A</li>
<li>(72 V) 1-Pole, 40 °C 25 A</li>
<li>(72 V) 1-Pole, 60 °C 25 A</li>
<li>(72 V) 1-Pole, 70 °C 22 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 22 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 22 A</li>
<li>Rated Operational Current DC-5 (Ie):(110 V) 1-Pole, 40 °C 4 A</li>
<li>(110 V) 1-Pole, 60 °C 4 A</li>
<li>(110 V) 1-Pole, 70 °C 4 A</li>
<li>(110 V) 2 Poles in Series, 40 °C 10 A</li>
<li>(110 V) 2 Poles in Series, 60 °C 10 A</li>
<li>(110 V) 2 Poles in Series, 70 °C 10 A</li>
<li>(110 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(110 V) 3 Poles in Series, 70 °C 22 A</li>
<li>(220 V) 2 Poles in Series, 40 °C 4 A</li>
<li>(220 V) 2 Poles in Series, 60 °C 4 A</li>
<li>(220 V) 2 Poles in Series, 70 °C 4 A</li>
<li>(220 V) 3 Poles in Series, 40 °C 9 A</li>
<li>(220 V) 3 Poles in Series, 60 °C 9 A</li>
<li>(220 V) 3 Poles in Series, 70 °C 9 A</li>
<li>(72 V) 1-Pole, 40 °C 9 A</li>
<li>(72 V) 1-Pole, 60 °C 9 A</li>
<li>(72 V) 1-Pole, 70 °C 9 A</li>
<li>(72 V) 2 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 2 Poles in Series, 70 °C 22 A</li>
<li>(72 V) 3 Poles in Series, 40 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 60 °C 25 A</li>
<li>(72 V) 3 Poles in Series, 70 °C 22 A</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 6 A / 144 W</li>
<li>(48 V) 2.8 A / 134 W</li>
<li>(72 V) 1 A / 72 W</li>
<li>(110 V) 0.55 A / 60 W</li>
<li>(125 V) 0.55 A / 69 W</li>
<li>(220 V) 0.27 A / 60 W</li>
<li>(250 V) 0.27 A / 68 W</li>
<li>(400 V) 0.15 A / 60 W</li>
<li>(500 V) 0.13 A / 65 W</li>
<li>(600 V) 0.1 A / 60 W</li>
<li>Rated Insulation Voltage (Ui):acc. to IEC 60947-4-1 690 V</li>
<li>acc. to IEC 60947-5-1 690 V</li>
<li>acc. to UL/CSA 600 V</li>
<li>Rated Impulse Withstand Voltage (Uimp):6 kV</li>
<li>Maximum Mechanical Switching Frequency:3600 cycles per hour</li>
<li>Rated Control Circuit Voltage (Uc):50 Hz 100 ... 250 V</li>
<li>60 Hz 100 ... 250 V</li>
<li>DC Operation 100 ... 250 V</li>
<li>Operate Time:Between Coil De-energization and NC Contact Closing 13 ... 98 ms</li>
<li>Between Coil De-energization and NO Contact Opening 11 ... 95 ms</li>
<li>Between Coil Energization and NC Contact Opening 38 ... 90 ms</li>
<li>Between Coil Energization and NO Contact Closing 40 ... 95 ms</li>
<li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li>
<li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li>
<li>Mounting by Screws (not supplied):2 x M4 screws placed diagonally</li>
<li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 0.75 ... 6 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 4 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 2.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 4 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 6 mm²</li>
<li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1x 0.75 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 2x 0.75 ... 1.5 mm²</li>
<li>Rigid Solid 1/2x 1 ... 2.5 mm²</li>
<li>Rigid Stranded 1/2x 1 ... 2.5 mm²</li>
<li>Wire Stripping Length:Auxiliary Circuit 10 mm</li>
<li>Control Circuit 10 mm</li>
<li>Main Circuit 10 mm</li>
<li>Degree of Protection:acc. to IEC 60529, IEC 60947-1, EN 60529 Auxiliary Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Coil Terminals IP20</li>
<li>acc. to IEC 60529, IEC 60947-1, EN 60529 Main Terminals IP20</li>
<li>Terminal Type:Screw Terminals</li>
</ul>
Technical UL/CSA
<ul>
<li>NEMA Size:00</li>
<li>Continuous Current Rating NEMA:9 A</li>
<li>Horsepower Rating NEMA:(115 V AC) Single Phase 1/3 Hp</li>
<li>(200 V AC) Three Phase 1-1/2 Hp</li>
<li>(230 V AC) Single Phase 1 Hp</li>
<li>(230 V AC) Three Phase 1-1/2 Hp</li>
<li>(460 V AC) Three Phase 2 Hp</li>
<li>(575 V AC) Three Phase 2 Hp</li>
<li>Maximum Operating Voltage UL/CSA:Main Circuit 600 V</li>
<li>General Use Rating UL/CSA:(600 V AC) 25 A</li>
<li>Horsepower Rating UL/CSA:(120 V AC) Single Phase 3/4 hp</li>
<li>(200 ... 208 V AC) Three Phase 2 hp</li>
<li>(220 ... 240 V AC) Three Phase 2 hp</li>
<li>(240 V AC) Single Phase 1-1/2 hp</li>
<li>(440 ... 480 V AC) Three Phase 5 hp</li>
<li>(550 ... 600 V AC) Three Phase 7-1/2 hp</li>
<li>Connecting Capacity Main Circuit UL/CSA:Rigid Solid 1/2x 16-10 AWG</li>
<li>Rigid Stranded 1/2x 16-10 AWG</li>
<li>Connecting Capacity Auxiliary Circuit UL/CSA:Rigid Solid 1/2x 18-14 AWG</li>
<li>Rigid Stranded 1/2x 18-14 AWG</li>
<li>Connecting Capacity Control Circuit UL/CSA:Rigid Solid 1/2x 18-14 AWG</li>
<li>Rigid Stranded 1/2x 18-14 AWG</li>
<li>Tightening Torque UL/CSA:Auxiliary Circuit 11 in·lb</li>
<li>Control Circuit 11 in·lb</li>
<li>Main Circuit 13 in·lb</li>
<li>Unit of Measurement : Pcs</li>
</ul>

abb af09-30-01-13 contactor 100-250vac/dc 3p 4kw 1nc kontaktor contactors para kontraktor penyentuh penghubung 接触器

abb-af09-30-01-13-contactor-100-250vac-dc-3p-4kw-1nc

Abb BC7-30-10-01 Contactor Mini 24VDC 3P 3NO

Catalog Description:BC7-30-10-01 Mini Contactor 24 V DC - 3 NO - 0 NC - Screw Terminals

Long Description:The BC7-30-10 mini contactor is a compact 3 pole contactor with 1 auxiliary contact and screw terminals. They are ideally suited for applications where reliability is a must and space is at a premium. Mini contactors are used in residential buldings, commercial buildings and industrial applications for the control of single or three-phase loads up to 5.5 kW (AC-3) and 20 A / 690 V (AC-1) or switching of control signals. Further features are the noiseless and hum-free coil, a switch position indication and the integrated possibility for rail or wall mounting.

<h3 class="md-block-header-three">Abb BC7-30-10-01 Contactor Mini 24VDC 3P 3NO</h3> <ul class="md-block-unordered-list-item"><li>Extended Product Type:BC7-30-10-01</li><li>Product ID:GJL1313001R0101</li><li>EAN:4013614150159</li><li>Catalog Description:BC7-30-10-01 Mini Contactor 24 V DC - 3 NO - 0 NC - Screw Terminals</li><li>Long Description:The BC7-30-10 mini contactor is a compact 3 pole contactor with 1 auxiliary contact and screw terminals. They are ideally suited for applications where reliability is a must and space is at a premium. Mini contactors are used in residential buldings, commercial buildings and industrial applications for the control of single or three-phase loads up to 5.5 kW (AC-3) and 20 A / 690 V (AC-1) or switching of control signals. Further features are the noiseless and hum-free coil, a switch position indication and the integrated possibility for rail or wall mounting.</li><li>Number of Poles:3</li><li>Mini Contactor Type:Mini Contactor</li><li>Rated Operational Voltage:Auxiliary Circuit 690 V AC</li><li>Auxiliary Circuit 250 V DC</li><li>Main Circuit 690 V AC</li><li>Main Circuit 220 V DC</li><li>Rated Frequency (f):Control Circuit DC</li><li>Main Circuit 60 Hz</li><li>Main Circuit 50 Hz</li><li>Main Circuit DC</li><li>Rated Impulse Withstand Voltage (Uimp):Auxiliary Circuit 6 kV</li><li>Main Circuit 6 kV</li><li>Rated Insulation Voltage (Ui):690 V</li><li>acc. to UL/CSA 600 V</li><li>Number of Main Contacts NC:0</li><li>Number of Main Contacts NO:3</li><li>Rated Operational Current AC-1 (Ie):(220 / 240 V) 40 °C 20 A</li><li>(220 / 240 V) 55 °C 16 A</li><li>(380 / 440 V) 40 °C 20 A</li><li>(380 / 440 V) 55 °C 16 A</li><li>(690 V) 40 °C 6 A</li><li>(690 V) 55 °C 6 A</li><li>Rated Operational Power AC-3 (Pe):(230 V) Three Phase 3 kW</li><li>(400 V) Three Phase 5.5 kW</li><li>(500 V) Three Phase 5.5 kW</li><li>(690 V) Three Phase, NO 3 kW</li><li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 96 A</li><li>Number of Auxiliary Contacts NC:0</li><li>Number of Auxiliary Contacts NO:1</li><li>Rated Operational Current AC-15 (Ie):(24 V) 4 A</li><li>(120 V) 4 A</li><li>(500 V) 2 A</li><li>(220 / 240 V) 4 A</li><li>(380 / 400 V) 3 A</li><li>Rated Operational Current DC-13 (Ie):(24 V) 2.5 A</li><li>(110 V) 0.7 A</li><li>(220 / 240 V) 0.4 A</li><li>Conventional Free-air Thermal Current (Ith):Main Circuit 20 A</li><li>Rated Control Circuit Voltage (Uc):24 V DC</li><li>Coil Operating Limits:(acc. to IEC 60947-4-1) for DC supply 0.85 ... 1.1 x Uc (at θ ≤ 55 °C)</li><li>Degree of Protection:Auxiliary Circuit Terminals IP20</li><li>Control Circuit Terminals IP20</li><li>Main Circuit Terminals IP20</li><li>Mechanical Durability:10000000 cycle</li><li>Minimum Switching Capacity:Auxiliary Circuit 17 V</li><li>Auxiliary Circuit 5 mA</li><li>Maximum Electrical Switching Frequency:(AC-1) 300 cycles per hour</li><li>(AC-15) 600 cycles per hour</li><li>(AC-3) 600 cycles per hour</li><li>(DC-1) 600 cycles per hour</li><li>(DC-13) 600 cycles per hour</li><li>(DC-3) 600 cycles per hour</li><li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible 1/2x 1 ... 2.5 mm²</li><li>Rigid 1/2x 1 ... 4 mm²</li><li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible 1/2x 1 ... 2.5 mm²</li><li>Rigid 1/2x 1 ... 4 mm²</li><li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li><li>Flexible 1/2x 1 ... 2.5 mm²</li><li>Rigid 1/2x 1 ... 4 mm²</li><li>Wire Stripping Length:Auxiliary Circuit 9 mm</li><li>Main Circuit 9 mm</li><li>Tightening Torque:Auxiliary Circuit 0.8 ... 1.1 N·m</li><li>Control Circuit 0.8 ... 1.1 N·m</li><li>Main Circuit 0.8 ... 1.1 N·m</li><li>Recommended Screw Driver:M3</li><li>Pozidriv 1</li><li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li><li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li><li>Power Loss:at Rated Operating Conditions per Pole 2 W</li><li>at Rated Operating Conditions AC-1 per Pole 1.4 W</li><li>Standards:IEC/EN 60947-1</li><li>IEC/EN 60947-4-1</li><li>IEC/EN 60947-5-1</li><li>UL 60947-1</li><li>UL 60947-4-1</li><li>Unit of Measurement : Pcs</li></ul>

<h3>Abb BC7-30-10-01 Contactor Mini 24VDC 3P 3NO</h3>
&nbsp;&nbsp;
<ul>
<li>Extended Product Type:BC7-30-10-01</li>
<li>Product ID:GJL1313001R0101</li>
<li>EAN:4013614150159</li>
<li>Catalog Description:BC7-30-10-01 Mini Contactor 24 V DC - 3 NO - 0 NC - Screw Terminals</li>
<li>Long Description:The BC7-30-10 mini contactor is a compact 3 pole contactor with 1 auxiliary contact and screw terminals. They are ideally suited for applications where reliability is a must and space is at a premium. Mini contactors are used in residential buldings, commercial buildings and industrial applications for the control of single or three-phase loads up to 5.5 kW (AC-3) and 20 A / 690 V (AC-1) or switching of control signals. Further features are the noiseless and hum-free coil, a switch position indication and the integrated possibility for rail or wall mounting.</li>
<li>Number of Poles:3</li>
<li>Mini Contactor Type:Mini Contactor</li>
<li>Rated Operational Voltage:Auxiliary Circuit 690 V AC</li>
<li>Auxiliary Circuit 250 V DC</li>
<li>Main Circuit 690 V AC</li>
<li>Main Circuit 220 V DC</li>
<li>Rated Frequency (f):Control Circuit DC</li>
<li>Main Circuit 60 Hz</li>
<li>Main Circuit 50 Hz</li>
<li>Main Circuit DC</li>
<li>Rated Impulse Withstand Voltage (Uimp):Auxiliary Circuit 6 kV</li>
<li>Main Circuit 6 kV</li>
<li>Rated Insulation Voltage (Ui):690 V</li>
<li>acc. to UL/CSA 600 V</li>
<li>Number of Main Contacts NC:0</li>
<li>Number of Main Contacts NO:3</li>
<li>Rated Operational Current AC-1 (Ie):(220 / 240 V) 40 °C 20 A</li>
<li>(220 / 240 V) 55 °C 16 A</li>
<li>(380 / 440 V) 40 °C 20 A</li>
<li>(380 / 440 V) 55 °C 16 A</li>
<li>(690 V) 40 °C 6 A</li>
<li>(690 V) 55 °C 6 A</li>
<li>Rated Operational Power AC-3 (Pe):(230 V) Three Phase 3 kW</li>
<li>(400 V) Three Phase 5.5 kW</li>
<li>(500 V) Three Phase 5.5 kW</li>
<li>(690 V) Three Phase, NO 3 kW</li>
<li>Rated Short-time Withstand Current Low Voltage (Icw):at 40 °C Ambient Temp, in Free Air, from a Cold State 10 s 96 A</li>
<li>Number of Auxiliary Contacts NC:0</li>
<li>Number of Auxiliary Contacts NO:1</li>
<li>Rated Operational Current AC-15 (Ie):(24 V) 4 A</li>
<li>(120 V) 4 A</li>
<li>(500 V) 2 A</li>
<li>(220 / 240 V) 4 A</li>
<li>(380 / 400 V) 3 A</li>
<li>Rated Operational Current DC-13 (Ie):(24 V) 2.5 A</li>
<li>(110 V) 0.7 A</li>
<li>(220 / 240 V) 0.4 A</li>
<li>Conventional Free-air Thermal Current (Ith):Main Circuit 20 A</li>
<li>Rated Control Circuit Voltage (Uc):24 V DC</li>
<li>Coil Operating Limits:(acc. to IEC 60947-4-1) for DC supply 0.85 ... 1.1 x Uc (at θ ≤ 55 °C)</li>
<li>Degree of Protection:Auxiliary Circuit Terminals IP20</li>
<li>Control Circuit Terminals IP20</li>
<li>Main Circuit Terminals IP20</li>
<li>Mechanical Durability:10000000 cycle</li>
<li>Minimum Switching Capacity:Auxiliary Circuit 17 V</li>
<li>Auxiliary Circuit 5 mA</li>
<li>Maximum Electrical Switching Frequency:(AC-1) 300 cycles per hour</li>
<li>(AC-15) 600 cycles per hour</li>
<li>(AC-3) 600 cycles per hour</li>
<li>(DC-1) 600 cycles per hour</li>
<li>(DC-13) 600 cycles per hour</li>
<li>(DC-3) 600 cycles per hour</li>
<li>Connecting Capacity Main Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible 1/2x 1 ... 2.5 mm²</li>
<li>Rigid 1/2x 1 ... 4 mm²</li>
<li>Connecting Capacity Auxiliary Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible 1/2x 1 ... 2.5 mm²</li>
<li>Rigid 1/2x 1 ... 4 mm²</li>
<li>Connecting Capacity Control Circuit:Flexible with Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible with Insulated Ferrule 1/2x 1 ... 2.5 mm²</li>
<li>Flexible 1/2x 1 ... 2.5 mm²</li>
<li>Rigid 1/2x 1 ... 4 mm²</li>
<li>Wire Stripping Length:Auxiliary Circuit 9 mm</li>
<li>Main Circuit 9 mm</li>
<li>Tightening Torque:Auxiliary Circuit 0.8 ... 1.1 N·m</li>
<li>Control Circuit 0.8 ... 1.1 N·m</li>
<li>Main Circuit 0.8 ... 1.1 N·m</li>
<li>Recommended Screw Driver:M3</li>
<li>Pozidriv 1</li>
<li>Mounting on DIN Rail:TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715</li>
<li>TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715</li>
<li>Power Loss:at Rated Operating Conditions per Pole 2 W</li>
<li>at Rated Operating Conditions AC-1 per Pole 1.4 W</li>
<li>Standards:IEC/EN 60947-1</li>
<li>IEC/EN 60947-4-1</li>
<li>IEC/EN 60947-5-1</li>
<li>UL 60947-1</li>
<li>UL 60947-4-1</li>
<li>Unit of Measurement : Pcs</li>
</ul>