Kleenguard

MILWAUKEE TOOL

Mechanical Parts

mechanical-parts

O Ring

o-ring

Safety

safety

Safety Gloves

safety-gloves

Nitrile is often referred to Buna (Buna-N) and NBR.

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C). 

It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.

However Nitrile are not a restricting factors in many applications.

Overview on Application Rating for Material Nitrile (NBR) 

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING JIS B2401 G22 ID 21.40 x CS 3.10Material : Nitrile (NBR) 70 ShoreNitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/nNhVwIyt~rBMYHnCz~A5gH.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G22
&nbsp;ID 21.40 x CS 3.10
Material : Nitrile (NBR) 70 Shore
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:fk4kl"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/nNhVwIyt~rBMYHnCz~A5gH.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="fk4kl" 
 layout="nodisplay"></amp-image-lightbox>

John

Others

Optibelt

Gates

SAMTECH

VITON

V Rings

Rubber Seals

Oil Seals

Shaft Couplings

Plumbing Tools & Equipment

Ball Bearings

Hydraulic Seals

Wall Plugs, Anchors, Fixings & Kits

Vee-Belts

buyerIntroduction

Oring Jis B2401 G22 Id 21.40 X Cs 3.10 Nitrile (nbr) 70 Shore

oring jis b2401 g22 id 21.40 cs 3.10 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.10腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-g22-id-21-40-x-cs-3-10-nitrile-nbr-70-shore

ORING JIS B2401 P22 ID 21.80 x CS 2.40Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/hk4zrIZZDfV2xPp4PYybSI.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P22&nbsp;
ID 21.80 x CS 2.40
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:25jn0"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/hk4zrIZZDfV2xPp4PYybSI.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="25jn0" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P22 ID 21.80 x CS 2.40 Nitrile (NBR) 70 Shore

oring jis b2401 p22 id 21.80 cs 2.40 nitrile (nbr) 70 shore 21,80 2,40 ring o-ring oem gelang oem/oem代工 2.40腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p22-id-21-80-x-cs-2-40-nitrile-nbr-70-shore

ORING ID 18 x CS 3 Nitrile (NBR) 70 Shore

ORING ID 18 x CS 3 Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage <ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png" alt="" /><figcaption class="md-block-image-caption"></figcaption></figure>

ORING ID 18 x CS 3 Nitrile (NBR) 70 Shore
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage

<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:8ab80"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="8ab80" 
 layout="nodisplay"></amp-image-lightbox>

oring id 18 cs nitrile (nbr) 70 shore nitril ring o-ring oem gelang oem/oem代工 腈纶 肖氏硬度 o型圈 oem代工

oring-id-18-x-cs-3-nitrile-nbr-70-shore

ORING ID 210 x CS 5 Nitrile (NBR) 70 Shore  

ORING ID 210 x CS 5 Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage <ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png" alt="" /><figcaption class="md-block-image-caption"></figcaption></figure>

ORING ID 210 x CS 5 Nitrile (NBR) 70 Shore&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage

<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:8ab80"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="8ab80" 
 layout="nodisplay"></amp-image-lightbox>

ORING ID 210 x CS 5 Nitrile (NBR) 70 Shore

oring id 210 cs nitrile (nbr) 70 shore nitril ring o-ring oem gelang oem/oem代工 腈纶 肖氏硬度 o型圈 oem代工

oring-id-210-x-cs-5-nitrile-nbr-70-shore

KleenGuard/Jackson Safety G80 Green Nitrile 18-inch 15mil Chemical Resistant Gauntlet GLOVES (per pair)

Jackson Safety G80 Nitrile Chemical Resistant Gauntlets are offer reliable protection against chemical and mechanical hazards.

Each hand specific latex-free glove provides longer length to protect wrist and lower forearm and allows full immersion.

The glove length is 46 cm long, with 22 mil thickness and sand patch texturing on fingers and palm offering enhanced wet and dry grip.

AQL 0.65 for pinholes provides superior protection ensuring you get jobs done efficiently and safely.

The gloves offer PPE category 3 protection for handling chemicals, oils, grease, alcohols, acids, bases or solvents also in immersion

and providing the highest level of abrasion resistance (4).

They are unlined to avoid the risk of linting and protect against contamination.

Perfect for use in Aerospace, Automotive, Metal Manufacturing, Food, Transportation and Construction.

Metal Fabrication & Furniture manufacturing

Machining operations using cutting oil and coolants

Cleaning and food handling in food industries

Code 25622 - 8/M
Code 25623 - 9/L
Code 25624 - 10/XL

Tested for Mechanical Protection : EN 388: 4101 – Abrasion, Cut, Tear, PunctureTested for Resistance to Permeation by Chemicals :EN 374-3:AJKTested for Microorganism Hazards  : EN374-1:2003 Level 3Protect from Heat and Radioactive Sources CE0120 - Category III PPE product certified according to Regulation (EU) EN420 

KleenGuard/Jackson Safety G80 Green Nitrile 18-inch 15mil Chemical Resistant Gauntlet GLOVES (per pair)<ul class="md-block-unordered-list-item"><li>Jackson Safety G80 Nitrile Chemical Resistant Gauntlets are offer reliable protection against chemical and mechanical hazards.</li><li>Each hand specific latex-free glove provides longer length to protect wrist and lower forearm and allows full immersion.</li><li>The glove length is 46 cm long, with 22 mil thickness and sand patch texturing on fingers and palm offering enhanced wet and dry grip.</li><li>AQL 0.65 for pinholes provides superior protection ensuring you get jobs done efficiently and safely.</li><li>The gloves offer PPE category 3 protection for handling chemicals, oils, grease, alcohols, acids, bases or solvents also in immersion</li><li>and providing the highest level of abrasion resistance (4).</li><li>They are unlined to avoid the risk of linting and protect against contamination.</li><li>Perfect for use in Aerospace, Automotive, Metal Manufacturing, Food, Transportation and Construction.</li></ul>Typical Uses:<ul class="md-block-unordered-list-item"><li>Chemical processing &amp; Oil refining</li><li>Metal Fabrication &amp; Furniture manufacturing</li><li>Automotive assembly and painting</li><li>Aerospace and automotive degreasing</li><li>Machining operations using cutting oil and coolants</li><li>Graphic arts and printing clean-up</li><li>Janitorial and public cleaning</li><li>Cleaning and food handling in food industries</li><li>Food Processing</li></ul>Code 25622 - 8/M Code 25623 - 9/L Code 25624 - 10/XLTesting MethodTested for Mechanical Protection : EN 388: 4101 – Abrasion, Cut, Tear, PunctureTested for Resistance to Permeation by Chemicals :EN 374-3:AJKTested for Microorganism Hazards  : EN374-1:2003 Level 3Protect from Heat and Radioactive Sources CE0120 - Category III PPE product certified according to Regulation (EU) EN420

KleenGuard/Jackson Safety G80 Green Nitrile 18-inch 15mil Chemical Resistant Gauntlet GLOVES (per pair)
<ul>
<li>Jackson Safety G80 Nitrile Chemical Resistant Gauntlets are offer reliable protection against chemical and mechanical hazards.</li>
<li>Each hand specific latex-free glove provides longer length to protect wrist and lower forearm and allows full immersion.</li>
<li>The glove length is 46 cm long, with 22 mil thickness and sand patch texturing on fingers and palm offering enhanced wet and dry grip.</li>
<li>AQL 0.65 for pinholes provides superior protection ensuring you get jobs done efficiently and safely.</li>
<li>The gloves offer PPE category 3 protection for handling chemicals, oils, grease, alcohols, acids, bases or solvents also in immersion</li>
<li>and providing the highest level of abrasion resistance (4).</li>
<li>They are unlined to avoid the risk of linting and protect against contamination.</li>
<li>Perfect for use in Aerospace, Automotive, Metal Manufacturing, Food, Transportation and Construction.</li>
</ul>
Typical Uses:
<ul>
<li>Chemical processing &amp; Oil refining</li>
<li>Metal Fabrication &amp; Furniture manufacturing</li>
<li>Automotive assembly and painting</li>
<li>Aerospace and automotive degreasing</li>
<li>Machining operations using cutting oil and coolants</li>
<li>Graphic arts and printing clean-up</li>
<li>Janitorial and public cleaning</li>
<li>Cleaning and food handling in food industries</li>
<li>Food Processing</li>
</ul>
Code 25622 - 8/M 
Code 25623 - 9/L 
Code 25624 - 10/XL
Testing Method
Tested for Mechanical Protection : EN 388: 4101 – Abrasion, Cut, Tear, PunctureTested for Resistance to Permeation by Chemicals :EN 374-3:AJKTested for Microorganism Hazards  : EN374-1:2003 Level 3Protect from Heat and Radioactive Sources CE0120 - Category III PPE product certified according to Regulation (EU) EN420&nbsp;

Paul Ang

STANLEY

MAKITA

BOSCH

Werner

WIHA

DEWALT

Other Tools

Ladders & Platforms

Door Hardware & Locks

Other Power Tools

Other Measuring Tools

Other Fittings

Drills, Impact Drivers & Wrenches

Power Tools Accessories

Gardening Hand Tools

Desk stationery

PowerFit Industrial Pte Ltd

KleenGuard/Jackson Safety G80 Green Nitrile 18-inch Long 22mil Chemical Resistant Gauntlet Gloves (per pair)

kleenguard/jackson safety g80 green nitrile 18-inch long 22mil chemical resistant gauntlet gloves (per pair) panjang 18-inci sarung tangan tahan kimia pasang) keselamatan kleenguard bahan (sepasang) kleenguard/ jackson/杰克逊 绿色丁腈橡胶 18 英寸长 耐化学品手套（每对） 安全手套 克莱恩加德

kleenguard-jackson-safety-g80-green-nitrile-18-inch-long-22mil-chemical-resistant-gauntlet-gloves-per-pair

Size: 8/M   (25622)

Size: 10/XL (25624)

Size: 9/L (25623)

Size

Milwaukee 48-22-8972 Impact Cut 3 Nitrile Dip Gloves - L 

SMARTSWIPE touchscreen compatible fingertips

<h3 class="md-block-header-three">Milwaukee 48-22-8972 Impact Cut 3 Nitrile Dip Gloves - L </h3>Features<ul class="md-block-unordered-list-item"><li>Impact Rated Enhanced TPR</li><li>Reinforced Nitrile Coating</li><li>High Dexterity Fingertips</li><li>SMARTSWIPE touchscreen compatible fingertips</li><li>18 Gauge</li><li>Webbing Pull Loop for easy wear</li><li>EN388 Abrasion: 4 (Range: 1-4)</li><li>EN388 Cut: 3 (Range: 1-5)</li><li>EN388 Tear: 4 (Range: 1-4)</li><li>EN388 Puncture: 2 (Range: 1-4)</li><li>EN388 (TDM Test) Cut: C (Range A-F)</li><li>ANSI Cut: A3</li></ul>

<h3>Milwaukee 48-22-8972 Impact Cut 3 Nitrile Dip Gloves - L&nbsp;</h3>
Features
<ul>
<li>Impact Rated Enhanced TPR</li>
<li>Reinforced Nitrile Coating</li>
<li>High Dexterity Fingertips</li>
<li>SMARTSWIPE touchscreen compatible fingertips</li>
<li>18 Gauge</li>
<li>Webbing Pull Loop for easy wear</li>
<li>EN388 Abrasion: 4 (Range: 1-4)</li>
<li>EN388 Cut: 3 (Range: 1-5)</li>
<li>EN388 Tear: 4 (Range: 1-4)</li>
<li>EN388 Puncture: 2 (Range: 1-4)</li>
<li>EN388 (TDM Test) Cut: C (Range A-F)</li>
<li>ANSI Cut: A3</li>
</ul>

Jimmy Foo

SCHNEIDER ELECTRIC

Philips

Thomas & Betts

BRADY

Bussmann

Weidmuller

FUJI

Crouse-Hinds

Fuses & Fusegear

Contactors

Plugs & Connector 

Light Bulbs

Led Lights

Circuit Breaker

Pilot Lights

Junction & Enclosure Box

Other Electrical Accessories

Doreen Tan

Milwaukee 48-22-8972 Impact Cut 3 Nitrile Dip Gloves - L

milwaukee 48-22-8972 impact cut nitrile dip gloves sarung tangan safety keselamatan tool celup nitril tool/密尔沃基工具 丁腈浸胶手套 安全手套 密尔沃基工具

milwaukee-48-22-8972-impact-cut-3-nitrile-dip-gloves-l

Milwaukee 48-22-8971 Impact Cut 3 Nitrile Dip Gloves - M 

<h3 class="md-block-header-three">Milwaukee 48-22-8971 Impact Cut 3 Nitrile Dip Gloves - M </h3>Features<ul class="md-block-unordered-list-item"><li>Impact Rated Enhanced TPR</li><li>Reinforced Nitrile Coating</li><li>High Dexterity Fingertips</li><li>SMARTSWIPE touchscreen compatible fingertips</li><li>18 Gauge</li><li>Webbing Pull Loop for easy wear</li><li>EN388 Abrasion: 4 (Range: 1-4)</li><li>EN388 Cut: 3 (Range: 1-5)</li><li>EN388 Tear: 4 (Range: 1-4)</li><li>EN388 Puncture: 2 (Range: 1-4)</li><li>EN388 (TDM Test) Cut: C (Range A-F)</li><li>ANSI Cut: A3</li></ul>

<h3>Milwaukee 48-22-8971 Impact Cut 3 Nitrile Dip Gloves - M&nbsp;</h3>
Features
<ul>
<li>Impact Rated Enhanced TPR</li>
<li>Reinforced Nitrile Coating</li>
<li>High Dexterity Fingertips</li>
<li>SMARTSWIPE touchscreen compatible fingertips</li>
<li>18 Gauge</li>
<li>Webbing Pull Loop for easy wear</li>
<li>EN388 Abrasion: 4 (Range: 1-4)</li>
<li>EN388 Cut: 3 (Range: 1-5)</li>
<li>EN388 Tear: 4 (Range: 1-4)</li>
<li>EN388 Puncture: 2 (Range: 1-4)</li>
<li>EN388 (TDM Test) Cut: C (Range A-F)</li>
<li>ANSI Cut: A3</li>
</ul>

Milwaukee 48-22-8971 Impact Cut 3 Nitrile Dip Gloves - M

milwaukee 48-22-8971 impact cut nitrile dip gloves sarung tangan safety keselamatan tool celup nitril tool/密尔沃基工具 丁腈浸胶手套 安全手套 密尔沃基工具

milwaukee-48-22-8971-impact-cut-3-nitrile-dip-gloves-m

Milwaukee Tool’s cut level 5 dipped gloves are designed to provide ultimate durability, all–day comfort, and best in class dexterity for handling small objects. Double dipped nitrile grip to provide best in class protection from puncture and added durability.

ANSI and EN cut level 5 protection to help prevent injuries from sharp objects on the jobsite 

SMARTSWIPE™ fingertips & palms provide full access to touchscreen devices

High dexterity fingertips to maximize control when handling small objects.

Milwaukee Tool’s cut level 5 dipped gloves are designed to provide ultimate durability, all–day comfort, and best in class dexterity for handling small objects. Double dipped nitrile grip to provide best in class protection from puncture and added durability.<ul class="md-block-unordered-list-item"><li>ANSI and EN cut level 5 protection to help prevent injuries from sharp objects on the jobsite </li><li>SMARTSWIPE™ fingertips &amp; palms provide full access to touchscreen devices</li><li>High dexterity fingertips to maximize control when handling small objects.</li></ul>Sizes : 48-22-8951 M , 48-22-8952 L

Milwaukee Tool’s cut level 5 dipped gloves are designed to provide ultimate durability, all–day comfort, and best in class dexterity for handling small objects. Double dipped nitrile grip to provide best in class protection from puncture and added durability.
<ul>
<li>ANSI and EN cut level 5 protection to help prevent injuries from sharp objects on the jobsite </li>
<li>SMARTSWIPE™ fingertips &amp; palms provide full access to touchscreen devices</li>
<li>High dexterity fingertips to maximize control when handling small objects.</li>
</ul>
Sizes : 48-22-8951 M , 48-22-8952 L